Fire

Part Numbers D9412GV4, D7412GV4, D9412GV3, D7412GV3, D7212GV3, D9412GV2, D9124GV2, D7412GV2, D7212GV2, D9412G, D9124G, D7412G, D7212G, D9112, D9124, D7212

Part numbers D7038, DS9484

Issue Control trouble # 87 displays Battery Trouble. Probable Cause: The battery failed a battery test The battery is defective The wiring to the battery is disconnected Solution: If there has just been a power failure, wait a least 24 hours for the battery to recharge, then perform a system reset to re-test the battery and clear the error Replace the battery. Check wiring.

DS7400Xi Version 3 and DS7400XI V3+

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G

This article response to the question if there is an automatic time sync between FSM and panel?

Part numbers DS284IS, D273IS

D282A

The D9124 is a 9000 control panel with a 24Vdc PSU and all the needed Fire Accessories for a basic system, all in one large red enclosure. See parts List below. The D9124 is made up of the following: D9112LTB, D9412LTB ,D9412GLTB, D9412GV2LTB - Control Panel D9101 - Red Enclosure D9100 - Carriers Module with the Following parts * * 2 - D192C - Bell Supervision Modules * 1 - D8125 - Popex Module * 1 - D928 - Dual Phone line Switcher * 1 - D9142LC - 24Vdc Power Supply D1256 - Fire Keypad D1601 - Hardwire Transformer

Part numbers D8024, D9061, D9051, D9052

This article answer to the question: " What is the maximum of simultaneous client connections supported on FSM?"

Have a look at this article and see how you can setup the FMS - OSD Logo

This article discusses how to send reports to the CS (Central Monitoring Station) from the FPA-1000-V2. We can network up to 8 of the FPA-1000-V2 panels together.  Each panel can report to the CS by itself, or one panel can report for all.  In either configuration, each panel needs its own unique account number.  

Part number D282A

Replace or upgrade - D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4,

Part numbers D10024A, D10024, D9024, D8024

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers D299, D290S, D281, D282, D283, D254, D255, D256, D257

Part numbers FPP-RNAC-8A-4C, D7038, DS9484, DS9400, DS9400I, DS9400M, D7024

The FPA-1000, FAP-1000-UL and FPA-1000-V2 all have the option to use 2 FPE-1000-SLC Loop cards. Each loop card on panel with Firmware less then 1.09 only support address 1 to 127 on each loop card, from firmware 1.10 and higher each loop card supports address 1 to 254. So it is possible to have to devices with the same address but on different loop cards. The the panel the keypad will display the following on the top line. The Event Type (Trouble, Fire, Supervisory) follow by XX-Y-AAA.A, (XX = Panel ID) (Y = Address Assignment, 0 - Web Page, 1 - SLC1, 2 - SLC2, Mainboard, or 4 - Option Bus) Followed (AAA.A The Device Address) .