Critical Communications: Dispatch

Question   C-Soft dongle key error codes - What do they mean?   Answer   Error 71 - Unable to read the key.  Most common error. To correct this error you will need to first check that you have a dongle key or a licensed AD-HB4 plugged into the computer. If you have a licensed AD-HB4 please contact telex technical support for further assistance. If there is a dongle key, then see the attached document to reload the driver for the dongle key. Error 13 - sp_io_communications_error. The system device driver is having problems communicating.  verify the device driver is correctly installed. If the driver is installed correctly, then try a different key if you have one. There may be a hardware issue with the key. If you do not have another key you will need to contact our customer service at 1-800-553-5992  

Question   How do I set up the DSP-223 for Optimum PTT Decoding?   Answer Figure 1 - A typical legacy analog radio system with a DSP-223 The most critical audio signal level in a legacy analog radio system, is the level of transmit audio from the console. It produces a signal that needs to be within a certain range as it arrives at the DSP-223/radio end of the system. Tone Remote Control (TRC) signaling must be within a certain level window, in order for the DSP-223 to decode it properly and reliably. With normal console functionality, the TRC levels and voice levels are calibrated relative to each other. Adjustment of the composite signal level at the console is sometimes necessary to compensate for line losses in the system. Figure 2 - Diagram of a Tone Remote Control burst Calibration of levels is primarily referenced to the Low Level Guard Tone (LLGT), it is typically -20 dBm. Voice then will fall into the window of approximately -20 to 0.0 dBm. The "Line RX" level pot on the front of the DSP-223 adjusts the Tx audio level coming in from the console. The DSP-223 sees audio from the console as "Line RX Audio".  This audio is then transferred by the DSP-223 to the radio via the Radio Tx line. The Radio Tx level adjustment potentiometer determines the level going into the radio, and thus, transmitter deviation. So decoder input and transmitter deviation are independently adjusted.   To find the optimum level for reliable PTT, first insure that the LLGT level is approximately -20 dbm at the input to the DSP-223. Some Motorola legacy consoles may produce a LLGT lower than -20, but the DSP-223 can work at lower levels if adjusted carefully.   Start with the Rx line level potentiometer at a low level (full ccw) and gradually increase it until the unit begins to decode the tone bursts, and indicated by the PTT led on the front panel. Repeated key ups are required while finding this point as the unit will not key off of just the LLGT itself. It requires the complete tone burst, which occurs then the PTT button is pushed on the console, to initialize a key up sequence. Key up the console at one or two second intervals while moving the Line Rx Level potentiometer, in order to determine the full range of decoding, which will occur over a portion of the potentiometers rotational range. The final set point should be approximately in the center of the arc where the decoding works. This helps insure that if the leased line electrical characteristics shift, as they typically will, the decoding of PTTs will continue to be reliable.               © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.

Question   How do I connect a Vertex Standard VXR-7000 Repeater to 223 Series Adapter Panel?   Answer   See attached;               © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   How do I set up Repeater Mode Linking using two DSP-223s?   Answer   Two DSP-223s are capable of creating RF links from console to remote base stations/repeaters, with the use of Repeater Mode. Repeater Mode introduces a 400 Ms delay in the TX path, and removes the Hold Tone/LLGT notch filter. When the DSP-223 at the far end detects the tone sequence, it PTTs the Base Station/Repeater, and passes TX audio, which is broadcast. As long as the hold tone is detected, it will hold the channel open. The reverse takes place with a receive signal present at the base station/repeater. This allows an RF link to be established with two mobile radios and two DSP-223s.  This can be useful as either a primary or backup link. This diagram shows two mobile radios configured to talk to each other.  They are connected to an analog console, and use Tone signaling. This allows control of the base station/repeater with Tone control.       To activate repeater mode, download the current configuration, check the “Repeater Mode” checkbox in the software, and write it back to the DSP-223.                 © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   What are the meanings of the DSP-223 terminal names?   Answer   The DSP-223 has several designations that define the audio paths that connect to it: Line RX Level is the audio signal "received" by the DSP-223 from the console, i.e. console transmit audio. Line TX Level is the RX radio audio sent to the console by the DSP-223. Radio RX Level is the RX audio signal coming into the DSP-223 from the radio receiver. Radio TX Level is the TX audio signal sent from the DSP-223 to the radio transmitter.  

Question   How do I set up ICOM IC-A200 Aircraft Radio to 223 Series Adapter Panels?   Answer   See attached;               © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   What is the latest firmware for the DSP-223? Where is the latest firmware for the DSP-223?   Answer   The latest firmware for the DSP-223 is 2.7. The latest Winapplication for the DSP-223 is 2.8 The versions 2.7 and 2.8 are compatible. You can find the firmware located at http://www.telex.com Please note: You will have to have an approved account to download the firmware. Please click here to make a download request http://www.telex.com/us/dispatch/account?f=DSP223%20v2.8%20load%20pack After approval you will then be able to download the firmware here. http://www.telex.com/us/dispatch/product/DSP-223_/1104 You will want to download the file named "DSP223 V2.8 load pack"               © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   What program do I use to program the DSP-223?   Answer   You will need to use the Winapp that is associated with the firmware of the DSP-223. For example, if the DSP-223 is on firmware version 2.6 you will need to use the Winapp version 2.6. *There is only one exception to this. If the DSP-223 is on firmware version 2.7, you can use the Winapp version 2.7 or 2.8. To download the latest firmware and the Winapp for the DSP-223 please click the link below. Please note: You will have to have an approved account to download the firmware. Please click here to make a download request. http://www.telex.com/us/dispatch/account?f=DSP223%20v2.8%20load%20pack After approval you will then be able to download the firmware here. http://www.telex.com/us/dispatch/product/DSP-223_/1104 You will want to download the file named "DSP223 V2.8 load pack"                 © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   How do I set up M/A COM ORION, J725M and M7100 Mobile Radios to 223 Series Adapter Panels?   Answer   See attached;                 © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   How do I set up 223 Series Adapter Panels to control Vertex Standard VX-5500 Series Radios?   Answer   See attached;               © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   How do I set up Kenwood TK-5110 Series Radio to 223 Series Adapter Panels?   Answer   See attached;                 © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   How do I set up ICOM IC-F121221 Series Radio to 223 Series Adapter Panels?   Answer   See attached;               © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   How do I set up Kenwood Radio TKR-x50 To 223 Series Adapter Panel?   Answer   See attached;               © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   How do I set up Motorola MCS-2000 Radios to 223 Series Adapter Panels?   Answer   See attached;                 © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   How do I set up Relm RM Series Radios to 223 Series Adapter Panels?   Answer   See attached;                 © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   How do I set up Vertex Standard VX-4100/4200 Series Radio To 223 Series Adapter Panels?   Answer   See attached;               © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   How do I set up Datron Guardian Series Mobile to 223 Series Adapter Panels?   Answer   See attached;                 © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   How do I set up Motorola XTL-5000 Radios to 223 Series Adapter Panels?   Answer   See attached;               © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   How do I set up Motorola CDM/GM/PRO Series Radios to 223 Series Adapter Panels?   Answer   See attached;             © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   How do I set up 223 Series radio adaptors to control ICOM IC-A110 Mobile Radio?   Answer   See attached;                 © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.