Critical Communications: Dispatch

Question How do I fix the ! in the device manager for my NR-V2? I have a missing driver for my NR-V2 where can I find it? PCI error in my NR-V2?   Answer The NR-V2 will have that error on it due to the onboard sound card. We purposely did not install the drivers for the onboard sound for the NR-V2. If we did that it would disable the sound card that we installed in the pc. This error will not cause any problems in the operation of the computer.           © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question My Network Recorder program will not open and gives an message saying " # defined active channels. Key allows for # channels." - why? Answer To get back into the Network Recorder you will have to delete a file and then reprogram the NR with the multicast addresses. This will reset the Network Recorder Multicast Table to factory defaults and will also enable you to run the program with a lower line Network Recorder key. After completing these steps you will need to reprogram the Multicast addresses of your IP-223’s that you want it to record: To reset the Multicast addresses in the Network Recorder, delete the file recordIP.telex  located at C:\Program Files\Telex Communications\Telex Network Recorder\DataFiles\ Reboot the Network Recorder and now you should be able to program the NR with the multicast addresses and then the NR program will run.             © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question How do I reset the Network Recorder SQL password?   Answer This article applys to NR-V2 Telex branded servers. You will need to be logged into the compuer as the administrator to complete the following steps. If you are unsure on how to complete these steps then please call our technical support at 1-800-898-6723 Here are the steps to clear the password: 1. Stop the MySQL501 Service 2. Open a file browser to E:\MySQL Server 5.0\data. Rename the ‘mysql’ directory to ‘mysql.old’ 3. Open the Add/Remove Programs wizard. Locate MySQL Server 5.0 and click change. Choose to repair it. Go through the steps to complete repair 4. If needed, restart the MySQL501 service 5. Open up Network Recorder. Enter a blank password. It should let you in.           © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question What files will I need backed up to fully restore Network Recorder?   Answer The locations that you need to backup will be listed as follows. All files in these directories need to be backed up. C:\Program Files\Telex Communications\Telex Network Recorder\DataFiles C:\Program Files\MySQL\MySQL Server 4.1 C:\Program Files\MySQL\MySQL Server 5.0 C:\TL Recorder Files E:\MySQL Server 4.1 E:\MySQL Server 5.0 E:\TL Recorder Files NOTE: You may not have some directories listed above, this is nothing to worry about.  This document covers our older NR and the newer NR-V2.           © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question How do I repair the database on the Telex Network Recorder?   Answer To repair the database, follow the steps below: 1. Open the database reviewer program and press and hold F9, then press F11, this will enable the repair options under the maintenance menu. 2. Click on "Maintenance" 3. Click on "Repair Database 1" , press OK at the prompt. Note: Time to complete will vary based on database size. 4. Click on "Repair Database 3" , press OK at the prompt. Note: Time to complete will vary based on database size. 5. After "Repair Database 3" is done, reboot the computer. 6. Restart the network recorder, you should now be able to access the Database and NR should be recording files again. NOTE: You should also perform these steps before any software upgrades to Network Recorders .                   © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.