Critical Communications: Dispatch

Question     I keep getting a Key Read error 71 on C-Soft or Network Recorder. Why and what can I do?   Answer     The PC has an issue with the drivers for the license dongle, reloading of drivers is required. Please check to make sure the donlge USB or Paralell key is plugged into the pc. Reboot the pc. Wait 2 minutes after logging into the pc and start the software program. If you still get key read errors please follow the rest of the steps to properly install the driver. You need to make sure that the dongle is unplugged. uninstall all drivers in add/remove programs referred to as sentinel or safenet or SPNcombo. Reboot computer. Install the latest driver from the safenet website. http://www.safenet-inc.com/support/tech/sentinel.asp Reboot computer again. Now plug the dongle key back in. Now download the key reader application and run it. This program should read the key and tell you how many lines it is programmed for. If this program finds the key then Csoft or Network Recorder should work for you.  http://www.telex.com/us/dispatch/file?i=97440&lg=eng  

Question   How do I fix the ! in the device manager for my NR-V2? I have a missing driver for my NR-V2 where can I find it? PCI error in my NR-V2?   Answer   The NR-V2 will have that error on it due to the onboard sound card. We purposely did not install the drivers for the onboard sound for the NR-V2. If we did that it would disable the sound card that we installed in the pc. This error will not cause any problems in the operation of the computer.           © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.  

Question   My Network Recorder program will not open and gives an message saying " # defined active channels. Key allows for # channels." - why? Answer   To get back into the Network Recorder you will have to delete a file and then reprogram the NR with the multicast addresses. This will reset the Network Recorder Multicast Table to factory defaults and will also enable you to run the program with a lower line Network Recorder key. After completing these steps you will need to reprogram the Multicast addresses of your IP-223’s that you want it to record: To reset the Multicast addresses in the Network Recorder, delete the file recordIP.telex  located at C:\Program Files\Telex Communications\Telex Network Recorder\DataFiles\ Reboot the Network Recorder and now you should be able to program the NR with the multicast addresses and then the NR program will run.             © Copyright Bosch Security Systems All rights reserved. Text, images, graphics, sound, animations and videos as well as the arrangement of the same in Bosch offline knowledgebase (help file) are protected by copyright and other intellectual property rights. The content of these offline knowledgebase may not be copied, disseminated, altered or made accessible to third parties for commercial purposes. Some Bosch web sites may also contain text, images, graphics, sound, animations and videos subject to third party copyrights. Warranty Note This information is provided by Bosch Security Systems ''AS IS'' and without warranty of any kind, expressed or implied, including (but not limited to) any implied warranties of merchantability, fitness for any particular purpose or non-infringement. While the information provided in believed to be accurate, it may include errors or inaccuracies. Bosch Security Systems will not be liable for any damages of any kind arising from use of this tool, including, but not limited to, direct, indirect, incidental, punitive and consequential damages.