Fire

Learn from this article how to enable usage type Fire on KD55 element from Bosch Remote Programming Software (RPS)

This articles shows where can you restart the activation or delay period in FSP-5000-RPS if a new activation is triggered

This article explains why the fire status display of the controller does not show all fire detectors in fire condition.

With FSM 5.6  the database.xml structure was slightly changed and FSM 5.6 is supporting only the new database.xml structure. This is leading after upgrade to a loss of the configured symbols (only the symbols, not the content of the devices configured on the floor plans). Therefore after upgrading from older FSM version (e.g. 5.2) to 5.6, the already configured symbols of sensors on maps are not shown correctly, they are shown are dots/circles.   Please note: If before executing the file provided below the application was opened and the sensor properties were edited by approving > at that step the symbols changed to the default symbol and the previously configured symbol cannot be recovered.

If the Item "Panel" is e.g. 1-1.1.1 respectively 1-1.SI_PANEL.1,then this item is the Group item of the panel system status items e.g. 1-1.1.1-1 till 1-1.1.1-10. Most of these system status items have NORMAL as value after startup, others can have ON, e.g. items from Condition Monitoring.

Use the tool provided when FSM server application is installed, to manage export/import of configurations. Please note: This tool is only for configuration backup and does not include logs and history.

One of the following programming keypads (FMR-DACT-KEYPAD, D7033, or DS9447) displays "SYSTEM FAULT" when programming one of  the following DACT models: D9068, DS9602, DCT-1, DCT-1E or FPT-DACT.

Products: B8512G, B9512G, B925F, B926F

A sticker on the front of the B450 indicates proper switch positions for selecting various SDI or Option Bus addresses (see figure 1). Figure 1 Sticker with address configurations   There are 2 types of FPD-7024 panels. It must first be determined which is in use before selecting the B450 address: Newer types with firmware version 1.06 and higher. These types are identified by icons on the keypad instead of words (see figure 2). Older types with firmware version 1.03 and lower. These types are identified by words on the keypad. Figure 2 Version 1.06 with Icons vs 1.03 with words   Version 1.06 & newer types: When used as sole communicator or backup to phone line, set the address wheel at 9 for Option Bus address 250. When used as backup to a primary network communicator, set the address wheel at 6 for Option Bus address 134. RPS connections require Option Bus address 250. Be sure the address wheel is set at 9 on the network communicator intended for RPS connections (Ethernet is preferred when allowed). Version 1.03 and older types: Use Option Bus address 250. Only one network communicator is available on these panel types.

Perform a sesitivity test on the following MUX smoke heads, D7050, D7050TH, D7050DH, MX250, MX250TH & MX250DH.

The point Index is set to (0), yet the point still displays in trouble at the keypad and as Extra Point in the panel History Log. How to correct this senario.

How to configure the FPD-7024 for various network reporting options. How does the FPD-7024 Network Communication alternate between devices?

Programming the FPD-7024 to report via ethernet to the CS with a DX4020 Network Card.

Configuring the FPP-RNAC-8A-4C on an Option Bus Fire panels FPD-7024 & FPA-1000.

AC Fail or Low Power Trouble on FPP-RNAC-8A-4C

How to access the Menu features on the B926F which does not have a Menu button.

The FLM-7024-ISO MUX bus isolator module is placed between devices on the MUX bus. A short on the bus causes activation of the isolators adjacent to either side of the short. This effectively separates all devices between the activated isolators from the rest of the bus. This prevents failure of the entire bus. When the short condition is removed, the isolators automatically restore the entire loop to normal operation.

  Part nummbers - FPE-1000-NE, FPE-1000-NF, FPE-1000-NW, FPA-1000-V2, FPA-1000  

FPA-1000, FPA-1000-V2, FPE-1000-NE, FPE-1000-NF, FPE-1000-NW

D125X Keypad is not displaying System Faults