Fire

Issue - Can the MUX data loop be run in the same cable of wire as the Keypad data wires? Solution - They cannot, they are two different data outputs.  They should never be run in the same jacketed of wire. They each require their own wire run and should at least 3 inches apart in the raceway. Part numbers DS7400X, DS7400Xi, DS7400, DS7400XIVER3+, DS7400XIVER4+, DS7400XIVER2, DS7430, DS7436, DS7447

In the event of flames and smoke, the camera's built-in intelligent algorithms analyze the scene in real time by concatenating and transforming the input data. Deep learning AI directly analyses the data and if a fire is confirmed, it triggers an alarm and sends a signal either to the fire panel or the Video Management System.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4,  

In this article you will find the amount of Pixels, Resolution and Scale of AVIOTEC IP Starlight 8000 Video-based fire detection

Part numbers D7212G , D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G, D8125MUX, D5060, B600

Part numbers D7035, DS9432, D7053, MX465, DS9465,

Part number D7024, FPD-7024, DS9400, DS9400I, DS9400M, D185, D7053

Part numbers D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers Ds7400, DS7400X

Part Numbers B8512G, B9512G, D9412GV4, D7412GV4, D9412GV3, D7412GV3, D7212GV3, D9412GV2, D9124GV2, D7412GV2, D7212GV2, D9412G, D9124G, D7412G, D7212G

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

This article contains a step-by-step guide about how you can set the field of view (FoV) of AVIOTEC IP starlight 8000

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4, DS7488

Part numbers D5200, D5200C, D5200CE

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9412, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G, D8004

Part numbers D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3,

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers D10024A, D10024, D9024, D8024, D328A

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

The operator 10000 is shown when detector fault/ Fire is acknowledged on the controller when no operator is logged in (e.g. Operator 2), by pressing the Acknowledge button.