Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Access Control

    Sort by:
    ‎05-16-2018 05:07 PM
    What is the part number for the wiring harness used on the Safecom SC2104E Radio SC2104
    View full article
    ‎05-16-2018 05:18 PM
    Safecom SC2104 end of line (EOL) resistors needed for supervised points SC2104
    View full article
    ‎05-16-2018 05:48 PM
    Safecom SC3100  radio set up to operate with power from external source SC3000
    View full article
    ‎05-16-2018 05:50 PM
    What are the correct output Voltages for terminal #2 Data and terminal 4 transmitter aux power of the C601 encoder? C601
    View full article
    ‎05-16-2018 05:52 PM
    How can I check the Audio Level on the C471R receiver for the Fastlink system?
    View full article
    ‎05-16-2018 05:53 PM
    What is the output impedance rating for the C472 transmitter and the C471R RF receiver on a Fastlink system? C471,C472
    View full article
    ‎06-22-2020 10:27 PM
    Set up Interlock APE 
    View full article
    ‎03-31-2020 10:10 PM
    1. Open “Card personalization Configuration”. You can find this software by accessing the “Access Professional Edition” folder in the start menu. See figure 1. If unable to find in the start menu, this is located in the folder “C:\BOSCH\Access Professional Edition\CP\bin\SfmCfgApp.exe”, (unless non-default paths and folder names are chosen during installation). See figure 2.   Figure 1 Figure 2 *Note: Make sure to run the software with administrator rights.   2. In Card personalization Configuration go to the Print tab.   Figure 3   3. Create a print channel. Type the print channel desired name and click the button to the left.   Figure 4 Once the print channel is created, the installed printers at this PC will populate below.     Figure 6   4. The printer’s information will auto fill under the current channel, modify parameters as needed.   Figure 7   5. Once finished, click apply and close.   Figure 8   6. Restart the computer.
    View full article
    ‎05-16-2018 05:54 PM
    Possible solution to transactions Not Displaying in AEC View Activity screen
    View full article
    ‎05-16-2018 05:55 PM
    Describes what the LpsSearch service is for.
    View full article
    ‎05-16-2018 05:56 PM
    This article explains a way to determine how many users are logged into ReadyKeyPro simultaneously.
    View full article
    ‎05-16-2018 05:57 PM
    Steps detailing connecting and initially configuring to an LNL-2220 access panel via the Web configuration page?
    View full article
    ‎05-16-2018 05:57 PM
    This article elaborates on the Alarm Monitoring display of an event message, "Failed to Report Expected Event".
    View full article
    ‎05-16-2018 05:58 PM
    ReadykeyPRO is changing some cardholder badges to Lost / Inactive / Returned status. What could be causing this?
    View full article
    ‎05-16-2018 05:59 PM
    This describes what triggers the AEC common relay output.
    View full article
    ‎05-16-2018 05:59 PM
    How is the transmitter and antenna system tested on a Fastlink radio system to insure good forward and reflective power C472
    View full article
    ‎04-01-2020 02:45 PM
    Issue APE logviewer repeatedly shows the message No. 542: “SQL-Server-Database online”, even when the SQL-Database is deactivated in the configurator.   Solution One possible solution would be the following: Manually modify the Active.acf file Before starting this process make sure the APE Configurator and Logviewer are closed. Create a backup of the Active.acf file. This file is located in the folder C:\BOSCH\Access Professional Edition\PE\Data\Cfg, (unless non-default paths and folder names are chosen during installation). Open the Active.acf file with a Notepad. Find the “sql server database” line and set activated to 0. “Activated=0” (see figure 1). Figure 1 Save the changes Restart BOSCH APE Service
    View full article
    ‎05-16-2018 06:00 PM
    Can I use a C472TP transmitter on a non private line tone system C472
    View full article
    ‎05-16-2018 06:01 PM
    How can I test the RF line card with a C601 Encoder without using a radio? C601,D6500
    View full article
    ‎05-16-2018 06:02 PM
    Is the transmitter tamper N/C or N/O? Is the SWR tamper N/C or N/O? Also, how does the SWR work, and what is the value of the EOL resistor? C472
    View full article
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist