Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Access Control

    Sort by:
    ‎03-08-2022 04:32 PM
    How do you configure First Card Unlock on the Access Easy Controller V2 so the door schedule does not unlock the door until someone has entered the building?
    View full article
    ‎03-07-2022 02:13 PM
    This article presents what is the compatibility of the ARD-AYCE658 Reader with AEC 2.1.
    View full article
    ‎03-07-2022 01:56 PM
    This article steps through the process of enabling the "pin or card" function in Access Professional Edition
    View full article
    ‎03-07-2022 01:58 PM
    This article explains what does a repeating low tone, high tone, and 1 sec pause mean on the AEC v. 2?
    View full article
    ‎03-07-2022 01:57 PM
    This article explains the message "Door already in use" from AECv2 when trying to delete a reader board
    View full article
    ‎02-28-2022 05:16 PM
    Reader Board 1 has three spare relays and each subsequent Reader Board has four spare relays.
    View full article
    ‎01-14-2022 07:37 AM
    Beginning with BIS 4.9.1 we changed the COM standard security settings to the values shown in this article
    View full article
    ‎12-20-2021 04:22 PM
    Find out from this article how the Gmail account can be configured in Bosch Access Easy Controller (AEC) 2.1.9.5 
    View full article
    ‎05-11-2018 01:52 PM
    These are steps to assist with troubleshooting the AEC 2.1 time drifting.
    View full article
    ‎09-21-2021 10:45 AM
      When logging to Access Management System (AMS), Visitor Management receive an error “Access Denied”.   Cause One possible cause is the user missing a “User profile”, or the User Profile doesn’t have execute rights for Visitor Management.   Solution One possible solution would be the following: Verify the user has a User Profile assigned. In AMS go to Configuration -> Operators and Workstations –> User rights Go to User Profiles, make sure to assign a profile if there is none.   Verify the Profile has execute rights for Visitor Management. Go to User Profiles, make sure the user profile assigned has provisioned the execution rights for Visitor Management. This rights may vary according to the user.   Note: The user and password to log in to Visitor Management are set under the “User account” tab.  
    View full article
    ‎09-21-2021 10:13 AM
    Disclaimer: this guide is intended for Windows advanced users. Knowledge on Windows registry and batch files is highly recommended. If you don’t have knowledge on modifying the Windows registry, do not continue as any mistake can damage the operating system.   Step-by-step guide   This document consists of three parts: Import or create a certificate to the RPS computer Enable Https and configure the certificate binding Import the certificate into AMS server  
    View full article
    ‎05-11-2018 01:42 PM
    Does the D6100 support a failover solution.
    View full article
    ‎06-19-2018 03:56 PM
    Filtering panel history in RAM IV/RPS/RPSLITE/RAMIV LITE RAMIV,RAMIV LITE,RPS,RPSLITE  
    View full article
    ‎06-19-2018 03:45 PM
    When connection is attempted for the first time with a DX4010i module to a 9000 series panel the RAMIV prompt displayed is "configuring port".  After approximately 90 seconds the RAMIV prompt will display "retry count exceeded" DX4020,DX4010,RPS,D9412,D9412G,D9412GV2,D9412GV3,D9412GV4,D7412,D7412G,D7412GV2,D7412GV3,D7412GV4,D7212,D7212G,D7212GV2,D7212GV3,D7212GV4
    View full article
    ‎06-19-2018 03:45 PM
    Cannot utilize DX4020 or D9133TTL-E for a RPS network connection, and the Network Interface Module's settings and software version have been verified as correct. DX4020,D9133TTL-E  
    View full article
    ‎06-29-2018 09:59 PM
    What does AED in RPS diagnostics mean RAM,RPS,RPS LITE
    View full article
    ‎06-14-2018 02:57 PM
    Article describes rdkypro "invalid badge, facility code and invalid card format" messages
    View full article
    ‎07-10-2018 09:06 PM
    Article describes "invalid badge, facility code and format" messages
    View full article
    ‎06-14-2018 02:38 PM
    This article will describe how to properly add onboard readers to an RkP-2220.
    View full article
    ‎06-14-2018 02:33 PM
    Article offers a possible solution for "free memory low" rdkypro message
    View full article
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist