Security: Intrusion

What is the default User Code for the Easy Series control panel.

How to determine the default user code for the Easy Series panel.ies panel.

How to determine the value of Easy Series End of Line Resistors.

How to enter program mode on the Easy Series control panel.

How to set the Easy Series control panel back to factory default settings.

How to determine the Easy Series primary power supply voltage.

How to interpret 'CALL FOR SERVICE' when logging into the Easy Series panel user menu.

How to interpret the flashing green circle on the Easy Series control panel. Easy Series,IUI-EZ1

How to interpret the flashing amber circle on an Easy Series control panel.

A BROKEN Green Circle could mean the following: Points are faulted and you can turn the system on to bypass those faulted points. Chime points are faulted and you would be hearing a Chime Tone. Both  conditions are occuring.

How to interpret a BROKEN Amber Circle on the EZ Series panel keypad.

Issue How do I turn the Chime Mode ON and OFF on the Easy Series Control panel?   Solution   Follow the steps below to turn the Chime Mode ON and OFF on the Easy Series Control panel: Hold the 4 key down on the keypad for 2-3 seconds and the panel will go into the Chime Mode sequence. Once in there you will press the 4 key as needed to turn the Chime Mode to either the ON or OFF position.

Issue How do I adjust the volume on the Easy Series Panels?   Solution   Follow the below step to adjust your control panel volume. Hold the 5 key down for 2-3 seconds and the Keypad will go into volume control mode.  Press the 5 key until the desired volume level is achieved. Volume Level Settings:  LOW - MEDIUM - HIGH - QUIET Note:  If the system is set for QUIET MODE then the Exit and Entry Delay tones will be SILENT.

Issue What is the phone voltage threshold for going into trouble?   Solution   The panel will show phone line trouble if the voltage is between 1.10vdc and 4.75vdc.

Issue How may users can the Easy Series panel hold?   Solution   The panel will hold up to a total of 22 users: 1:  Master user 2 to 21: System users User 22: Duress user

Issue What brand of 2 wire smokes will work with the Easy Series panel, and how many can be applied to the loop? Solution Radionics/DS D285TH MB2W, MB2WL, D287, D288 = 20 D263 = 20 D263 = 20 D263C = 20 D263S = 20 D263TH = 20 D263THC = 20 D265AW D250AW = 12 D286 MB2W, MB2WL, D287, D288 = 20 D603 MB2W, MB2WL = 20 D604 MB2W, MB2WL = 20 D605 MB2W, MB2WL = 20 DS260 MB2W, MB2WL, D287, D288 = 20 DS230 MB2W, MB2WL = 20 DS230F MB2W, MB2WL = 20 DS233F MB2W, MB2WL = 20 DS250 MB2W, MB2WL, D287, D288 = 20 DS250TH MB2W, MB2WL, D287, D288 = 20 DS260 MB2W, MB2WL, D287, D288 = 20 DS282 = 20 DS282C = 20 DS282S = 20 DS282TH = 20 DS282THS = 20   Bosch Security Systems F220P/PTH F220-B6, -B6C, -B6E, -B6R = 20 1151 B110LP = 15 1451 B401B = 15 2151 B110LP = 15 2400 N/A = 15   System Sensor 2400TH = 15 2451 B401B = 15 2451TH B401B  = 15

Issue What are the steps on silencing the fire alarm, and resetting the control panel? Solution Present your token twice, or enter your pass code twice.

Issue Unable to get the token reader to work when the UI is mounted to a metal surface. Solution The IUI-EZ1 cannot  be mounted directly to a metal surface. The UI needs to be separated by at least 3 inches of non-conductive material between the metal surface.

Issue What are the wire length limits for the command center?   Solution   Minimum wire length = 10 feet Maximum wire length = 328 feet

Issue What are the steps to start and end the phone session programming?   Solution   1. House Phone: Press the # key three times, and enter the passcode when prompted. Default ( 5432 ) 2. Outside Phone: Dial the house phone number, and press * key three times when the call is answered, Enter a passcode when prompted 3. Installers Quick Connect: Connect a phone set to the control panel's test post. Press and hold the test button for approximately 15 seconds. Enter a passcode when prompted. Note: To end the phone session, Press the # key repeatedly until the system says "goodbye".