Bosch Building Technologies

    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    100% helpful (1/1)
    ‎07-10-2018 08:01 PM
    Issue How do I turn the Chime Mode ON and OFF on the Easy Series Control panel?   Solution   Follow the steps below to turn the Chime Mode ON and OFF on the Easy Series Control panel: Hold the 4 key down on the keypad for 2-3 seconds and the panel will go into the Chime Mode sequence. Once in there you will press the 4 key as needed to turn the Chime Mode to either the ON or OFF position.
    View full article
    100% helpful (2/2)
    ‎06-01-2023 06:56 PM
    Best practices to download and Install Remote Programming Software (RPS).
    View full article
    ‎07-17-2018 08:58 PM
    What is the default User Code for the Easy Series control panel.
    View full article
    ‎07-17-2018 08:26 PM
    How to determine the default user code for the Easy Series panel.ies panel.
    View full article
    ‎07-17-2018 08:28 PM
    How to determine the value of Easy Series End of Line Resistors.
    View full article
    ‎07-17-2018 08:14 PM
    How to enter program mode on the Easy Series control panel.
    View full article
    ‎07-17-2018 07:54 PM
    How to set the Easy Series control panel back to factory default settings.
    View full article
    ‎07-17-2018 07:38 PM
    How to determine the Easy Series primary power supply voltage.
    View full article
    ‎07-17-2018 07:10 PM
    How to interpret 'CALL FOR SERVICE' when logging into the Easy Series panel user menu.
    View full article
    ‎07-17-2018 07:00 PM
    How to interpret the flashing green circle on the Easy Series control panel. Easy Series,IUI-EZ1
    View full article
    ‎07-17-2018 06:55 PM
    How to interpret the flashing amber circle on an Easy Series control panel.
    View full article
    ‎07-17-2018 06:41 PM
    A BROKEN Green Circle could mean the following: Points are faulted and you can turn the system on to bypass those faulted points. Chime points are faulted and you would be hearing a Chime Tone. Both  conditions are occuring.
    View full article
    ‎07-17-2018 06:37 PM
    How to interpret a BROKEN Amber Circle on the EZ Series panel keypad.
    View full article
    ‎07-10-2018 07:59 PM
    Issue How do I adjust the volume on the Easy Series Panels?   Solution   Follow the below step to adjust your control panel volume. Hold the 5 key down for 2-3 seconds and the Keypad will go into volume control mode.  Press the 5 key until the desired volume level is achieved. Volume Level Settings:  LOW - MEDIUM - HIGH - QUIET Note:  If the system is set for QUIET MODE then the Exit and Entry Delay tones will be SILENT.
    View full article
    ‎07-10-2018 06:40 PM
    Issue What is the phone voltage threshold for going into trouble?   Solution   The panel will show phone line trouble if the voltage is between 1.10vdc and 4.75vdc.
    View full article
    ‎06-26-2018 05:49 PM
    Issue How may users can the Easy Series panel hold?   Solution   The panel will hold up to a total of 22 users: 1:  Master user 2 to 21: System users User 22: Duress user
    View full article
    ‎06-25-2018 06:17 PM
    Issue What brand of 2 wire smokes will work with the Easy Series panel, and how many can be applied to the loop? Solution Radionics/DS D285TH MB2W, MB2WL, D287, D288 = 20 D263 = 20 D263 = 20 D263C = 20 D263S = 20 D263TH = 20 D263THC = 20 D265AW D250AW = 12 D286 MB2W, MB2WL, D287, D288 = 20 D603 MB2W, MB2WL = 20 D604 MB2W, MB2WL = 20 D605 MB2W, MB2WL = 20 DS260 MB2W, MB2WL, D287, D288 = 20 DS230 MB2W, MB2WL = 20 DS230F MB2W, MB2WL = 20 DS233F MB2W, MB2WL = 20 DS250 MB2W, MB2WL, D287, D288 = 20 DS250TH MB2W, MB2WL, D287, D288 = 20 DS260 MB2W, MB2WL, D287, D288 = 20 DS282 = 20 DS282C = 20 DS282S = 20 DS282TH = 20 DS282THS = 20   Bosch Security Systems F220P/PTH F220-B6, -B6C, -B6E, -B6R = 20 1151 B110LP = 15 1451 B401B = 15 2151 B110LP = 15 2400 N/A = 15   System Sensor 2400TH = 15 2451 B401B = 15 2451TH B401B  = 15
    View full article
    ‎06-25-2018 03:07 PM
    Issue What are the steps on silencing the fire alarm, and resetting the control panel? Solution Present your token twice, or enter your pass code twice.
    View full article
    ‎06-25-2018 02:57 PM
    Issue Unable to get the token reader to work when the UI is mounted to a metal surface. Solution The IUI-EZ1 cannot  be mounted directly to a metal surface. The UI needs to be separated by at least 3 inches of non-conductive material between the metal surface.
    View full article
    ‎06-25-2018 03:02 PM
    Issue What are the wire length limits for the command center?   Solution   Minimum wire length = 10 feet Maximum wire length = 328 feet
    View full article
    Top Contributors