Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎08-02-2018 08:35 PM
    Issue The FA113 will not arm the panel if it was disarmed from the keypad and will not disarm if panel was armed from the keypad Solution Used as an arm/disarm device, the FA113 is configured to panel zone 74 or 194. Pressing the FA113 Off button sends an OPEN signal to the control panel and pressing the On button sends a NORMAL signal to the control panel. The area should be both Armed and Disarmed by the FA113 for it to function correctly. When the arming state is changed by the FA113, then by another means, the FA113 becomes unable to detect the current armed state of the area and will not respond to the keys pressed. Correct settings for FA113: The transition of the state of point 74 is what causes the area to arm or disarm. • Mode in the D8125INV is set to 4. • Keyswitch Maintained point (Point Type 4) with  Point Response 2, is  required for  the FA113. • Area will arm with a transition from open to normal on point 74. • Area will disarm with a transition from normal to open on point 74. The FA113 is also used for panic on point 75 (7412G) and point 195 (9412G).
    View full article
    ‎08-02-2018 04:01 PM
    There are 2 tests performed on the FA206i, Walk Test and Transmission Test. Walk Test: With cover in place, quickly (less than 1/2 second) pass a magnet near the Test Mode reed switch. This will activate a 1 minute walk test mode where the LED will light with each trip but no alarm signals will be transmitted. Transmission Test: With cover in place, hold a magnet near the Test Mode reed switch for at least one second. This will activate a one minute transmission test mode where the device will transmit alarm and restoral cycles at regular intervals for 1 minute. Note:  The FA206i LED only lights when in test mode.
    View full article
    ‎08-02-2018 08:33 PM
    Overview: The Inovonics FA570 and FA575 High-Power Repeaters receive, decode and re-transmit signals from Inovonics FA-Series transmitters up to 4 miles in open field. Issue What is the difference between the FA570 and FA575? Solution The difference is the FA575 includes the ACC640 weatherproof enclosure to accommodate exterior applications as well as battery leads to hookup an external battery. Other then that, the units are exactly the same.
    View full article
    ‎08-01-2018 10:45 PM
    Part numbers FA113, FA400, D8125INV, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B600, B8512G, B9512G
    View full article
    ‎07-31-2018 10:38 PM
    Overview: The FA422 Programming Cable has a 2 pin female connector at the transmitter end. Inovonics transmitters have 3 pins on them. The center pin on the transmitter is for Data and the 2 outer pins are ground. The 2 pin connector connects to the center pin and either of the outer pins on the transmitters when programming. Issue The programming cable for the FA422 receiver only has 2 pins at the transmitter end. How does the 2 pin connector connect to the 3 pin transmitter? Solution Connect the 2 pin connector to the center pin and either outer pin. Either way will work.
    View full article
    ‎07-30-2018 10:18 PM
      How to determine whether the Inovonics repeater can be installed outside. ISW‑EN5040‑T, EN5040‑T, Repeater, Echostream.  
    View full article
    ‎07-27-2018 07:36 PM
    How to use the ISW-D8125CW-V2 and D8125INV on the same panel. Can the D8125INV be connected to a panel that already has an ISW-D8125CW-V2 connected?
    View full article
    ‎07-25-2018 07:21 PM
    Issue What is the Bosch part number for the Inovonics FA206DS wireless motion detector?   Solution   The Bosch part number for the FA206DS would be the DS775RF and is used with the Inovonics FA400 receiver and the Bosch D8125INV wireless interface for Bosch D7412G/D9412G control panels.
    View full article
    ‎07-24-2018 04:10 PM
    How to select a panel type when using Inovonics wireless keyfobs. Is the EN1224-ON or FA113 compatible with D7212 panel types (G, GV2, or GV3)? D7212G,D8125INV,FA113 Keychain Remote Control
    View full article
    ‎07-19-2018 09:46 PM
    How to determine the number of EN1224-ON fobs are available on a G series control panel.
    View full article
    ‎07-17-2018 06:31 PM
    How to select the correct transfomer for the FA575 Repeater.
    View full article
    ‎07-11-2018 06:28 PM
    Issue An FA400 receiver that is disconnected will not force the keypad to display a missing message.   Solution   If two FA400 receivers are being used on the same D8125INV, the "Receiver Missing" message will not display if only one of the receivers is disconnected.
    View full article
    ‎06-28-2018 09:35 PM
    How to program 7000/9000 thru GV3 panels to work with the D8125INV and Inovonics wireless points.
    View full article
    ‎06-15-2018 05:06 PM
    Overview When wireless points are faulted, they display as 'Short' to the panel. When the wireless point tamper switch is faulted it will display as an 'Open' to the panel. Issue The panel when using a D8125INV and wireless points shows normal/faulted when point transitions from normal to off normal but the control always shows shorted. Solution Problem may be caused by another point expander connected to the control panel. Remove D8125INV from control panel and determine if points go missing. If points remain active (normal, faulted, etc) the control panel is interfacing with the points through another addressable point expander. Part numbers D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G, D8125INV, ISW-D8125CW, ISW-D8125CW-V2, FA400, EN4200
    View full article
    ‎06-14-2018 07:42 PM
    FA210 REDUCED-SIZE UNIVERSAL TRANSMITTER Available in off-white (FA210). For use with any standard contact or sensor, this reduced-size universal transmitter comes with case tamper and supports an end-of-line resistor. Mounting bracket included for quick and easy installation. FA210W REDUCED-SIZE “WIDE GAP” DOOR/WINDOW TRANSMITTER Available in off-white (FA210W). Same as the FA210 but includes two built-in magnetic reed switches, one on top, and one on the side for maximum flexibility. Includes magnet that supports a 5/8” gap. Can support a N/O or N/C external contact when using the reed switch. USed with the FA400 Receiver
    View full article
    ‎06-08-2018 03:35 PM
    How to interpret the message at the wireless interface: 'Range Limited', and correct the issue.
    View full article
    ‎06-07-2018 03:10 PM
    How to determine if the ISW-EN5040 is indicating AC Loss or Low Battery.
    View full article
    ‎06-06-2018 09:43 PM
    How to troubleshoot why the FA113 arm/disarm keyfob generates a RF Low Battery Response on the panel keypad. How to troubleshoot the FA113 generating a RF Low Battery Response on the panel keypad. When pressing both Star keys on the FA113 generates Servc RF Low Battery response on Command Center.
    View full article
    ‎06-04-2018 05:22 PM
    Determine compatibility of the wireless interface with the panel type and firmware revision.   B820 Wireless interface and EN4200 receiver. Compatible with GV4 panel types, B-Series panels and B8512G/B9512G. The B820 connects to the SDI2 Bus. ISW-D8125CW-V2 Wireless interface and EN4200 receiver. Compatible with G series with rev6.3+ through GV4 when connected to the Zonex bus or B8512G/B9512G when using the B600 retrofit module. ISW-D8125CW Wireless interface and ISW-EN7280 (ISW-TRL8080/ISW-EN4200) receiver. Compatible with G series with rev6.3+ through GV4 when connected to the Zonex bus or B8512G/B9512G when using the B600 retrofit module. D8125INV Wireless interface and FA400 receiver. Compatible with G series with rev6.3+ through GV4 when connected to the Zonex bus or B8512G/B9512G when using the B600 retrofit module. Determine compatibility of transmitters by the wireless interface type and receiver date code. EN4200 with date code 11048 and newer (date code is yyddd where yy=year and ddd=day): Works with transmitters designated with ENxxxx or ISW-ENxxxx part numbers. EN4200 with date code 11047 and older (date code is yyddd where yy=year and ddd=day): Works only with transmitters designated with ISW-ENxxxx part numbers. Compatible Transmitters designated with ENxxxx part numbers. Requires EN4200 with date code 11048 or newer; EN1223D Water‑resistant Pendant Panic EN1223S Water‑resistant Pendant Panic EN4200 Wireless receiver EN1233D Necklace Pendant Panic EN1233S Necklace Pendant Panic EN1235D Belt-clip Panic EN1235S Belt-clip Panic EN1235SF Fixed Location Panic EN1235DF Fixed Location Panic EN1210EOL Universal Transmitter w/ EOL EN1210W Door-Window Transmitter w/Reed Switch EN1215EOL Universal Transmitter with Wall Tamper & EOL Survey Transmitter EN1215WEOL Door‑window Transmitter w/ Wall Tamper, Reed Switch, & EOL EN1260 PIR Transmitter EN1262 PIR Transmitter EN1265 PIR Ceiling Motion EN1261HT PIR High-traffic EN1242 Smoke EN1247 Glassbreak EN1249 Billtrap ISW-TRL8080 EN7280 Receiver/Translator Kit EN4204R LED Receiver EN4216R LCD Receiver EN5040-T High‑power Repeater EN7016 Wireless Survey Kit EN1210SK Compatible Transmitters designated with ISW-ENxxxx part numbers: ISW-D8125CW-V2 Wireless Interface ISW-EN4200 Wireless receiver ISW-EN1223D Water‑resistant Pend Panic ISW-EN1223S Water‑resistant Pend Panic ISW-EN1233D Necklace Pendant Panic ISW-EN1233S Necklace Pendant Panic ISW-EN1235S Belt-clip Panic ISW-EN1235D Belt-clip Panic ISW-EN1235SF Fixed Location Panic ISW-EN1235DF Fixed Location Panic ISW-EN1210EOL Universal Transmitter w/ EOL ISW-EN1210W Door-Win Transmitter w/Reed Switch ISW-EN1215EOL Universal Transmitter with Wall Tamper & EOL ISW-EN1215WEOL Door‑window Transmitter w/ Wall Tamper, Reed Switch, & EOL ISW-EN1260 PIR Transmitter ISW-EN1262 PIR Transmitter ISW-EN1265 PIR Ceiling Motion ISW-EN1261HT PIR High-traffic ISW-EN1242 Smoke ISW-EN1247 Glassbreak ISW-EN1249Billtrap ISW-TRL8080 Translator ISW-EN7280 Receiver/Translator Kit ISW-EN4204R LED Receiver ISW-EN4216R LCD Receiver ISW-EN5040-T High‑power Repeater ISW-EN7016 Wireless Survey Kit ISW-EN1210SK Survey Transmitter
    View full article
    ‎06-01-2018 02:53 PM
    How to use the EN1210W or ISW-EN1210W with external contacts. The EN1210W or ISW-EN1210W will not go normal when the external contacts are strapped out.
    View full article
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist