Fire

Part number FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9431, D7039, FPE-7039

Part Numbers D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D192C, D192G

*Note: DS9431 MUX was replaced by the D7039, The D7039 was replaced by the FPE-7039

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2,

Part numbers D7024, D7038

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7465, DS7465i, D8125MUX, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G, B600, D5060, D7053, FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part mumbers D9068, D9052, D8024, D9024, D40024, D10024A, D7033, FMR-DACT-KEYPAD

Perform these steps to enable the D7024, FPD-7024, DS9400, DS9400I, and DS9400M for RPS programming via phone line with a compatible RPS modem: Press (0) Enter Program Mode. Enter Pin (Default is 9876). Press (6) Accounts. Press (4) Ring Count. Set Ring Count to (02) #. Press the (*) key two times or until you see PROGRAM MODES. Press (3) System. Press (7) Remote Program. Press (1) Enable. Press the (*) key five times to Exit Program Mode. You need to dial Line 1 on the panel. It is the second line down on the panel (it is NOT the line in the top right). Before connecting with RPS, perform an Auto-Learn with at least one Mux Device connected to the Mux loop, then send your RPS program to the panel. Press (0) Enter Program Mode. Enter Pin (default is 9876). Press (9) Program Mux. Press (4) Auto Program. Press (1) Yes.

 Program Menu for the DS9400, DS9400I and DS9400M

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400, RPS, DX4010-V2,

Panel part numbers - FPD-7024, FPA-1000, FPA-1000-UL, and FPA-1000-V2. Network Card part numbers for the FPD-7024, DX4020, B420, and B426. Cellular option for the FPD-7024 part numbers B450 (Interface for Cellular Card) B440, B441, B442, B443, and B444.

How to upgrade the D5070 Programmer to program addresses 128 through 254.

Part numbers D7212,D7412, D9112, D9124, D9412, D7212G,D7412G, D9112G, D9124G, D9412G, D7212GV2,D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7447, DS7447E

Issue D8112 Displays CPU FAIL. Solution D8112 Displays CPU FAIL Remove Data wires from terminals 30 and 31. Copy the panel via RAMii, RPS or D5200 and save the copy. Send the panel a NEW RECORD or Blank Account. (Basically set the panel back to factory default.) Reload the regional copy back in the panel. Reattach the Data wires to terminals 30 and 31. If still in CPU FAIL - Rewrite the saved copy of the program and save as a different file name. Remove Data wires from terminals 30 and 31. Send the panel a NEW RECORD or Blank Account. Send the new file into the panel. Reattach the Data wires to terminals 30 and 31. If still in CPU FAIL -  replace the panel.

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G

The point Index is set to (0), yet the point still displays in trouble at the keypad and as Extra Point in the panel History Log. How to correct this senario.

AC Fail operation in the following panels. D7212GV2, D7412GV2, D9412GV2, 7212GV3, D7412GV3, D9412GV3, 7212GV4, D7412GV4, D9412GV4, B8512G and B9512G.

Part numbers D10024A, D10024, D9024, D8024, D328A, D323A, D324A