Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎06-27-2018 05:37 PM
    Issue If using the D220A on the D2112 do I have the Exit Feature? Solution No, the D2112 does not have the Exit Feature. It uses the "Step Out Feature". The Exit Feature does appear on page 23 of the Users Guide, but that is because this Keypad can also be used on other 2000 Series Panels which have the Exit Feature.
    View full article
    ‎06-27-2018 05:31 PM
    Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U D2812P, D168A
    View full article
    ‎06-25-2018 07:18 PM
    Issue What is the open air range on the 2 button and 4 button ITI keyfobs?   Solution   The 60-607-319.5 two button and the 60-606-319.5 four button ITI keyfobs are 500 feet open air transmitters.
    View full article
    ‎06-25-2018 06:53 PM
    D5200 Programmer:  The D5200 needs to match a Data Lock code in the panel to access programming. Changing the panel Data Lock Code from the default of 12345 will prevent access. Remote Programming Software: RPS also needs to match the Data Lock code in the panel to access programming.  Changing the panel Data Lock Code from the default of 12345 will prevent access. RPS also needs to match the RPS Passcode (or RAM Passcode in legacy types) in order to allow access programming. Changing the default from 999999 will block RPS access.
    View full article
    ‎06-25-2018 06:45 PM
    How to interpret Alarm Recent Close reports from a 2000 series control panel. D2212,D2012,D2112,D2412,D2812
    View full article
    ‎06-25-2018 06:37 PM
    Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U D2812P
    View full article
    ‎06-25-2018 04:28 PM
    How to determine the Keypad Capacity of the D2112 control panel. D2112,D202A,D220A
    View full article
    ‎06-21-2018 10:19 PM
    When attempting to use the Excursion mode feature on a 2000 series panel, why does the keypad prompt the user to enter a passcode after pressing the Clear key? D2212,D2412,D2812  
    View full article
    ‎06-20-2018 10:43 PM
    Part numbers D2212, D2212B, D2212BE, D2412, D2812, D223, D223A, D222, D222A, D220, D220A, D202, D202A
    View full article
    ‎06-20-2018 05:52 PM
    Part number D2212, D2212B, D2212BE, D2412, D2812
    View full article
    ‎06-20-2018 05:51 PM
    How to  renew One Time Passcodes on 2000 series panels. D2212,D2412,D2812,D222A LCD,D223A LCD,D202A,D220A,D222,D223  
    View full article
    ‎06-19-2018 10:10 PM
    How to determine which pins of the RJ45 and RJ11 are used for Tip and Ring or Tip-House/Ring-House.
    View full article
    ‎06-19-2018 02:20 PM
    Can the D220A Keypad be used with a D2112? How to determine which resistor to cut from the D220A Keypad to work with a D2112 panel. D220A (8 led),D2112,D2412,D2812,D2212.
    View full article
    ‎06-18-2018 10:58 PM
    How to add a passcode on the 2000 Series panel using a Text Keypad. D2212, D222A LCD, D223A LCD, D222,D223, D2412,D2812
    View full article
    ‎06-18-2018 10:49 PM
    How to configure a keyswitch point on a 2000 Series panel. D2212, D2412, D2812
    View full article
    ‎06-18-2018 09:50 PM
    How to address LED keypads addressed to work with the D2212/D2412/D2812.
    View full article
    ‎06-15-2018 09:13 PM
    How to program the 2000 Series for expanded points and configure the B208 device address.
    View full article
    ‎06-15-2018 08:44 PM
    Part numbers D192C, D192G, D2212, D2212E, D2212BE, D2412, D2812
    View full article
    ‎06-15-2018 06:13 PM
    Issue Can I mix Heat Detectors and 2 wire smokes with a sounder when using a D132A Smoke Detector Polarity Reversing Module? Solution No. When a Heat detector goes into alarm it puts a short on the input zone to indicate the alarm. The D132A uses Aux power from the panel when the polarity reversal takes place and since a heat detector does not reset when polarity is reversed, it would put a direct short on the Aux power of the panel. Consequently everything connected to the same Aux power terminals would not function.
    View full article
    ‎06-15-2018 03:27 PM
    Issue What is the difference between the D133 an D134? Solution The D133 has a single relay rated at 2A @ 30 VDC – 0.6A @ 125 VAC. The D134 has two relays rated at 2A @ 30 VDC – 0.6A @ 125 VAC. Current draw for the Relay is 40 mA per relay when activated.
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist