Security: Intrusion

How to force the DS7240/DS7220 to answer remote programming software. DS7240,DS7220,DS7445I,DS7447I

Issue How does the phone line monitor for the DS7100 operate?   Solution   If the monitor detects a phone line fault for more than 50 seconds, the power LED will begin to flash.  If the audible output has been enabled in line 89, the keypad sounder will pulse every ten seconds if the control is disarmed. If the panel is armed, the siren output will activate. To ascertain if the trouble condition is indeed a phone line failure, enter # 87 at the keypad. The display will indicate "Communication Failure". If the "System Trouble Report" (line 51) is programmed the system will try to send this report. A phone line failure may be caused by: A cut or missing phone line. A reversed connection (Tip, and Ring Reversed) A miswired jack To clear the error; Determine the cause of the failure and eliminate the cause. After eliminating the cause of the failure, wait at least ten seconds. The error will clear if the problem has been eliminated and the LED will stop flashing provided a failure has not occurred on the central station phone numbers. If a failure has occurred at the central station restore by entering # 87 * at the keypad.

How to determine how many keypads are supported on the DS7060 and allowed wire distance. DS7060,DS7447,DS7445,DS7443

How to determine how many command centers (keypads) are supported by the D7112. How many command centers can be supported on the D7112?

How to determine the number of passcodes are available in the D7112. How many passcodes can the D7112 panel have?

  Issue Symptom The keypad displays Oct. Relay Fault. Probable Cause The octal relay module ( DS7488 ) is defective or the wiring to the module is defective. There is not a DS7488 or a DS7488 has been removed from the system. Solution Check the wiring to the module. Enter the programming mode. This will rescan the options bus and clear the problem. Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,  DS7488

Issue Multiplex troubles and loss of communication to devices.   Solution   Perform the Following Troubleshooting steps 1. Check the voltage on the Mutilplex Bus 2. If the Voltage is 12VDC 3. Check and make sure the panel is out of programmer’s mode 4. Look for duplicate addresses 5. *Disable Bus lock 6. Make sure 12VDC is not connect to the Multiplex bus If the Voltage is 0 - . 3VDC 1. Check for Shorts on the multiplex loop 2. Check for reverse polarity to devices 3. If the device require diodes make sure the cathode side is on the positive side. * To Disable Bus Lock 1. Enter in to Programmers Mode  by code + #0 2. Type in 9999 *5 Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7430, DS7436

How to determine the capacity of the D7112 panel event log. How many events are held in the D7112 panel log?

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7447, DS7447E

How to program Passcode Duress on the D7212B,  D7212B1, D9112B or D9112B1

How to interpret the WDSRP log entry: ARMED LEVEL 2 from a DS7060 control panel.

How to view System Troubles on the DS7240/DS7220. DS7240,DS7220,DS7445I,DS7447I

How to view the panel log file using the DS7447 keypad. DS7400X,DS7400,DS7400Xi,DS7400XIVER3+,DS7400XIVER4+,DS7400XIVER2,DS7447I,DS7447E,DS7447