The keypad is beeping every ten seconds for no apparent reason. The keypad is not displaying any troubles. How do I stop the keypad from beeping? DS7400Xi,DS7400,DS7400XIVER2,DS7400XIVER3+,DS7400XIVER4+,DS7400X

View full article

687 Views

0 Comments

‎05-23-2018 08:38 PM

How to tell what a flashing partial light means on the DS7100

What does the partial light flashing mean on the keypad, and how is it cleared? DS7100

View full article

546 Views

0 Comments

‎05-23-2018 04:56 PM

How to clear troubles from the D1254 keypad connected to the D7112 panel

How do I clear troubles on a D1254 keypad connected to a D7112? D7112,D1254

View full article

499 Views

0 Comments

‎05-23-2018 08:33 PM

How to determine why all zone led's are flashing on the D720 keypad

On a D720, why are all the zone lights flashing? D9412,D7412,D7212,D9412G,D7412G,D7212G,D9412GV2,D7412GV2,D7212GV2,D9412GV3,D7412GV3,D7212GV3,D9412GV4,D7412GV4,D7212GV4,D7212B,D7212B1,D9112,D9112B,D9112B1

View full article

1554 Views

0 Comments

100% helpful (1/1)

‎05-23-2018 08:20 PM

How to clear the last event from alarm memory on the keypad

How can the command center be cleared after an alarm condition on the 7000/9000 series panels? D7412G,D9412G,D9412,D7412,D7212,D7212G,D9412GV2,D7412GV2,D7212GV2,D9412GV3,D7412GV3,D7212GV3,D9412GV4,D7412GV4,D7212GV4,D1255,D1260

View full article

7135 Views

0 Comments

‎05-23-2018 03:51 PM

How to keep the keypad from sounding the trouble tone with CMD 47

The keypad is giving a trouble tone after a CMD 47 is entered to reset the smoke detectors. D7412G,D9412G,D7212,D7212B,D7212B1,D7212G,D7412,D9112,D9112B,D9112B1,D9412,D1255,D1260,D720,D7412GV2,D9412GV2,D7212GV2,D9412GV3,D7412GV3,D7212GV3,D9412GV4,D7412GV4,D7212GV4,B9512G,B8512G,B920,B930,B942

View full article

537 Views

0 Comments

‎05-23-2018 02:08 PM

How to calibrate the D1265 keypad display.

View full article

1681 Views

0 Comments

‎05-23-2018 08:14 PM

How to configure a point to be used only as a Watch Point.

Definition: Watch Mode Only- This point will not create alarm or trouble responses and will not generate reports to the Central Monitoring Station. Program the Point: Select Point Type= 0. Select all Yes/No options= NO. Set Alarm Report Routing = 0: No Reports, No Events to Log/Printer. Set Restoral Report Routing = 0: No Reports, No Events to Log/Printer. Select Watch Tone and enable Watch Point: Select [Cmd] + 62 to select the watch tone. Select [Cmd] + 63 to select the watch point(s).

View full article

1030 Views

0 Comments