How can the command center be cleared after an alarm condition on the 7000/9000 series panels?
D7412G,D9412G,D9412,D7412,D7212,D7212G,D9412GV2,D7412GV2,D7212GV2,D9412GV3,D7412GV3,D7212GV3,D9412GV4,D7412GV4,D7212GV4,D1255,D1260
The B8512 or B9512 supervises keypads even when disabled Related Products B8512 B9512 B915 B920 B921C B925F B926F B930 B942 Overview Issue The B8512 or B9512 supervises keypads even when Supervision=NO Solution If the keypad Type is set to an SDI type keypad (see below) the supervision setting can be configured YES or NO. When the keypad Type is set to one of the SDI2 type keypads the supervision Yes/No setting is ignored and the keypad is supervised. SDI2 devices are always supervised by design regardless of the supervision setting. SDI Keypads SDI2 Keypads D1255 VFD Keypad (SDI) B915 D125xRB Keypad (SDI) B920 D126x LCD Keypad (SDI) B921C B925F B926F B930 B942 Notes SDI2 devices that are the same type of device must use different addresses. SDI2 devices that are not the same type can be configured to the same address. For example: The B915, B92x, B930 or B942 are all same device types (keypads) and must use different addresses. The B920, B208 and B520 are all different device types and can all use the same address.
Keypad programming is available in GV3 panels with firmware revision 8.10 or higher.
NOTE: Keypad programming is not available during while an RPS programming session is active, or when any area is armed.
Enter from normal operation:
Press [9]+[9]+[Enter].
Select Keypad Programming. The keypad displays Enter Passcode.
Enter the service passcode (default= 123).
Enter from service mode (reset pin closed):
D1255:
Set the address to 16 with dipswitch: 1-5= OFF and 6= ON. The keypad displays Enter Passcode when the reset pin is closed.
Enter the service passcode (default= 123).
D1260:
Set the address to 8 with dipswitch: 1-3= OFF and 4-6= ON. The keypad displays Enter Passcode when the reset pin is closed.
Enter the service passcode (default= 123).
The following options are available upon entering keypad programming:
Phone Numbers – Phone 1 thru Phone 4
Phone Format - Phone 1 thru Phone 4
Enhanced Comm – Path 1 thru 4
Routing
Route Groups 1 thru 4
RPS Parameters
RPS Passcode
RPS Phone Number
RPS IP Address
RPS IP Port
Area Parameter – 1 thru 32
Account On – Yes / No
Account Number
Command Center 1 thru 16
Enhanced Command Center – Yes / No
Command Center Scope –
User Pass Code
User 0 (Install Passcode)
User 1 (User Passcode)
Point Parameters
D9412GV3: 1-247
D7412GV3: 1-75
D7212GV3 1 -40
Point Index
Disable Keypad Programming
Overview: User is entering passcode twice to arm alarm system. A five second delay between key strokes will cause the keypad to view the next entry as the start of a NEW passcode. Key strokes must be strung together with no pauses in between longer that 5 seconds.
Issue
User must enter passcode twice to arm the system. Same code is used for both entries.
Solution
The user is pausing too long between key strokes. After a key is pressed the next key stroke must be pressed wthin 5 seconds. A delay of 5 or more seconds will cause the keypad to view the next key stroke as the start of a new entry.
