Bosch Building Technologies

    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎05-23-2018 04:56 PM
    How do I clear troubles on a D1254 keypad connected to a D7112? D7112,D1254
    View full article
    ‎06-12-2018 09:56 PM
    How to determine how many keypads are supported on the DS7060 and allowed wire distance. DS7060,DS7447,DS7445,DS7443
    View full article
    ‎06-07-2018 03:03 PM
    How to determine D1255RB, D1256RB and D1257RB command center compatibility with G-Series control panels.
    View full article
    ‎06-12-2018 09:40 PM
    How to correct when the command center goes blank as soon as the last area arms. Why does the command center goes blank as soon as the last area arms?
    View full article
    ‎05-24-2018 08:32 PM
    What steps are required to program the ITI wireless points on a D2000 Series panel? D2212,D2412,5600E,D223A,D208RF,D216RF,D222A
    View full article
    ‎05-18-2018 04:49 PM
    What other keypads will work with the D4112 panel besides the D420? D4112,D636A,D620,D420A,D626
    View full article
    ‎06-29-2018 03:30 PM
    Issue What scope should be used when programming the D720 keypad?   Solution   The D720 keypad must be programmed AREA WIDE scope only. Account or Panel Wide scopes are not supported by this keypad.   Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, D720
    View full article
    ‎06-17-2018 08:27 PM
    Issue Can I change the user text on a 7000-9000 series panel via the keypad? Solution You may only change the users name via a keypad if you have a D1260 keypad.  Follow the steps below to make the changes. >Command 56 then Passcode >Choose the user number and press ENTER >Press the soft key menu item CONTINUE >Press the soft key menu item NAME >Follow the soft key menu to move left/right and to change the characters in the name. >After you done with the modifications press the soft key menu item CONTINUE >If this is correct you press the soft key menu item YES >If it is not correct then press the soft key menu item NO After you have completed your task press the soft key menu item EXIT D1260 Compatible Control Panels • B9512G/B9512G-E • B8512G/B8512G-E • D9412GV4/D7412GV4/D7212GV41 • D9412GV3/D7412GV3/D7212GV31 • D9412GV2/D7412GV2/D7212GV21 • D9412G/D7412G/D7212G • D9412, D7412, D7212, and D9112 with firmware versions 6.40 or higher
    View full article
    ‎06-19-2018 10:24 PM
    How to clear alarm memory on the D720 keypad.
    View full article
    ‎06-15-2018 09:33 PM
    How to correct the D1260 error: Incorrect panel programming, enhanced should be set to yes.
    View full article
    ‎06-04-2018 06:39 PM
    How to use the D1260 or D1265 when the address is not programmed as Enhanced.
    View full article
    ‎05-22-2018 03:42 PM
    How is the keypad's display brightness changed? DS7400XIVER3+,DS7447I
    View full article
    ‎05-17-2018 09:10 PM
    What is the process for bypassing a point on a D7000/D9000/G Series control panel? D7412G,D9124,D9412,D9412G,D7412,D7212,D1255,D1260,D1255R,D9412GV3,D7412GV3,D7212GV3,d9412GV2,D7412GV2,D7212GV2,D9412GV4,D7412GV4,D7212GV4
    View full article
    ‎06-18-2018 09:50 PM
    How to address LED keypads addressed to work with the D2212/D2412/D2812.
    View full article
    ‎06-01-2018 04:01 PM
    The D4412 and D6412 use the D621, D623 or D625 command centers. Pressing All-On or Part-On on the will arm only the area where the keypad is assigned. Command 50 may be used to move to an area other than the programmed assigned area.  After moving to the selected area, press either All-on or Part-on to arm the area. Command 80 may be used to arm all areas. Command 81 may be used to disarm all areas. Note:  Commands 80 and/or 81 must be enabled by an individual with assigned authorization to perform the function. Use Command 50 to move to another area and arm:  Press [CMD] [5][0] and enter a valid code if required. The keypad will scroll through all available areas. Press the desired area number to move to the area.  Press All-On or Part-On to arm the selected area.  Pressing and holding [CMD] will exit the Command 50 feature returning the keypad to its “home” area. Use Command 80 to arm All Areas: Press [CMD] [8][0] and enter a valid code if required.       Hold down the All On key for 2 sec and it forces all areas to All On.  Use Command 81 to disarm All Areas:  Press [CMD] [8][1] and enter a valid code if required. The keypad will indicate all areas are off.
    View full article
    ‎07-16-2018 10:11 PM
    How to determine how many command centers (keypads) are supported by the D7112. How many command centers can be supported on the D7112?
    View full article
    ‎07-02-2018 03:19 PM
    Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7447, DS7447E
    View full article
    ‎06-15-2018 06:22 PM
    Part numbers D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D1252, D1252A
    View full article
    ‎06-14-2018 02:21 PM
    How to correct the D1255 Command Center going blank while selecting menus. While entering key stroke commands and using the Menu option on the D1255, the display blanks out and the speaker crackles then the display comes up after 5 seconds.
    View full article
    ‎06-01-2018 09:53 PM
    How to configure the the GV3 v8.10+ for using a D1260 or D1265 with keypad programming.
    View full article