Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎06-25-2018 04:15 PM
    What relay configuration setting activates a relay with CMD 47?
    View full article
    ‎06-25-2018 04:06 PM
    How to program Passcode Duress on the D7212B,  D7212B1, D9112B or D9112B1
    View full article
    ‎06-25-2018 03:50 PM
      Issue The D192G panel zone (point) is in trouble and the yellow LED is not on. Solution With the zone/point in trouble and No Yellow LED On there is a wiring fault. One of the following terminals do not have power connected to them. External Power In (EXT PWR IN) Auxiliary Power In (AUX PWR IN) Terminal 1 (AUX PWR IN) 13.75 VDC Terminal 2 (Common) Terminal 3 (Supervised Zone / Point) 2.50 VDC Normal Condiction < 1.50 VDC In Trouble Condiction Terminal 4 (Trigger) 13.75 VDC  In Alarm Only Terminal 5 (External Power In) 12 VDC or 24 VDC Depended on needed Output for the NAC's or Power Supply Terminal 6 (Common) This is the Common from an 24 VDC External Power Terminal 7 (Positive Alarm Output) Terminal 8 (Negative Alarm Output)
    View full article
    ‎06-25-2018 03:44 PM
    Issue The D279 or D279A will not recover the default passcode while following the instructions. Solution You are performing this procedure while one of the D279A zones is not in a normal condition. Normalize D279A zones and the default procedure will work.      
    View full article
    ‎06-25-2018 03:36 PM
    Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,
    View full article
    ‎06-25-2018 03:26 PM
    How to interpret the WDSRP log entry: ARMED LEVEL 2 from a DS7060 control panel.
    View full article
    ‎06-25-2018 03:20 PM
    D7112 Overview: Firmware Revision 3.57 is NOT compatible with the D7112 panels with a date code of X9416 or higher.   Issue   Panel is non responsive to any programming.   Solution   Firmware Revision 3.57 is NOT compatible with the D7112 panels with a date code of X9416 or higher.
    View full article
    ‎06-25-2018 03:13 PM
    Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,
    View full article
    ‎06-25-2018 03:07 PM
    Issue What are the steps on silencing the fire alarm, and resetting the control panel? Solution Present your token twice, or enter your pass code twice.
    View full article
    ‎06-25-2018 03:02 PM
    Issue What are the wire length limits for the command center?   Solution   Minimum wire length = 10 feet Maximum wire length = 328 feet
    View full article
    ‎06-25-2018 02:57 PM
    Issue Unable to get the token reader to work when the UI is mounted to a metal surface. Solution The IUI-EZ1 cannot  be mounted directly to a metal surface. The UI needs to be separated by at least 3 inches of non-conductive material between the metal surface.
    View full article
    ‎06-22-2018 09:43 PM
    How to program the test report on a D9000, G Series, or GV2 Series control panel.
    View full article
    ‎06-22-2018 09:19 PM
    How to bypass the tamper input on the DX2010.
    View full article
    ‎06-22-2018 09:14 PM
    How to determine the wiring requirements for the multiplex bus and zone loops. DS7400X,DS7400,DS7400Xi,DS7400XIVER2,DS7400XIVER3+,DS7400XIVER4+,DS7461i,DS7460i,DS7465i,DS7457i,DS7432
    View full article
    ‎06-22-2018 08:29 PM
    How to correct the error message  "RAM CARD NOT PRESENT" when updating D5200 handlers.
    View full article
    ‎06-22-2018 08:08 PM
    How to correct zones not showing faulted in disarm state on of D4112/D6112 panel keypad. D6112,D4112,D420A (6 led),D620,D636A.
    View full article
    ‎06-22-2018 07:25 PM
    How to correct the D8128A is inoperative when wired according to terminal labeling. D7212B,D7212B1,D9112B,D9112B1,D8129,D7112
    View full article
    ‎06-22-2018 03:37 PM
    I just replaced my external modem with a new one, and when connecting to a panel the status screen never moves from (configuring port). D5500C-LITE-LPT,D5500C-LITE-USB,D5500C-LPT,D5500C-USB,D5500CU,D5500CU-LITE,RAM,RAM IV - D5370,RAMIV,RAMIV LITE,RPS,RPS LITE
    View full article
    ‎06-22-2018 03:13 PM
    I upgraded my computer. Started using an external modem for communication instead of using the Tecmar internal modem (d9350/9351) and am getting an “invalid or missing hardware key communication unavailable" error. RAM,RAM IV - D5370,RAMII,RAMIII,RAMIV,RPS
    View full article
    ‎06-22-2018 03:13 PM
    When at the panel list in RPS, the account number slot is missing from the panel records list view. RPS,RAMIV,RAMIV LITE,RPS LITE
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist