Fire

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9465I, MX465, D7035, D7053

Part numbers D9412GV4, D7412GV4, D9412GV3, D7412GV3, D7212GV3, D9412GV2, D9124GV2,D7412GV2, D7212GV2, D9412G, D9124G, D7412G, D7212G, D9412, D9124, D9112, D7412, D7212, D192C, D192G

Panel part numbers DS7400XIVER3+, DS7060, DS7090, DS7090I, DS7090TM, DS7080I, DS7080IVER2, DS7080IP32, DS7090TMI, DS7100, DS7400, DS7400XIVER2, DS7400XIVER4+, DS7400X, DS7400Xi

Issue - Can the MUX data loop be run in the same cable of wire as the Keypad data wires? Solution - They cannot, they are two different data outputs.  They should never be run in the same jacketed of wire. They each require their own wire run and should at least 3 inches apart in the raceway. Part numbers DS7400X, DS7400Xi, DS7400, DS7400XIVER3+, DS7400XIVER4+, DS7400XIVER2, DS7430, DS7436, DS7447

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers FPD-7024,  D7024, DS9400, DS9400I, DS9400M, D7053, D7035, DS9465I, MX465, DS9432,

The programmer for the DACT family (D9068,FPT-DACT; DCT-1; DCT-1E; DS9602) is one of the following: D7033 DS9447 FMR-DACT-KEYPAD Notes The FMR-DACT-KEYPAD is not the same as the FMR-7033. The FMR-7033 will not program the D9068 DACT family (FPT-DACT; DCT-1; DCT-1E; DS9602).

Part numbers D125B, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9112G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, 7412GV4, D9412GV4, B8512G, B9512G

 Program Menu for the DS9400, DS9400I and DS9400M

Part Numbers - D7024, FPD-7024, DS9400, DS9400I, DS9400M

Bosch part numbers D340, DS290, D263, D263TH, D263THC, D263THS, DS282, DS282TH, DS282THC, DS282THS, F220-B6, F220-P, D287, D288, D285, D285DH

Part Numbers D7024, FPD-7024, DS9400, DS9400I, DS9400M

Part Numbers D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D192C, D192G

Part number list, DS9400, DS9400I, DS9400m, D7024, FPD-7024, D7053, D7035, D7039, FPE-7039,DS9431, DS9431R, MX465, DS9465, DS9465I, DS9432.

Perform these steps to enable the D7024, FPD-7024, DS9400, DS9400I, and DS9400M for RPS programming via phone line with a compatible RPS modem: Press (0) Enter Program Mode. Enter Pin (Default is 9876). Press (6) Accounts. Press (4) Ring Count. Set Ring Count to (02) #. Press the (*) key two times or until you see PROGRAM MODES. Press (3) System. Press (7) Remote Program. Press (1) Enable. Press the (*) key five times to Exit Program Mode. You need to dial Line 1 on the panel. It is the second line down on the panel (it is NOT the line in the top right). Before connecting with RPS, perform an Auto-Learn with at least one Mux Device connected to the Mux loop, then send your RPS program to the panel. Press (0) Enter Program Mode. Enter Pin (default is 9876). Press (9) Program Mux. Press (4) Auto Program. Press (1) Yes.

AC Fail operation in the following panels. D7212GV2, D7412GV2, D9412GV2, 7212GV3, D7412GV3, D9412GV3, 7212GV4, D7412GV4, D9412GV4, B8512G and B9512G.

Only one keypad can be used at a time on the FPD-7024. Your keypad options are the builtin keypad on the FPD-7024, the FMR-7033, or the FMR-7036.

DS9400, DS9400M, D7024, and FPD-7024 Fire Alarm Panels the Water-Flow timer operation.

Configuring the FPP-RNAC-8A-4C on an Option Bus Fire panels FPD-7024 & FPA-1000.

AC Fail or Low Power Trouble on FPP-RNAC-8A-4C