Fire

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4, DS7447

Panel part numbers DS7400XIVER3+, DS7060, DS7090, DS7090I, DS7090TM, DS7080I, DS7080IVER2, DS7080IP32, DS7090TMI, DS7100, DS7400, DS7400XIVER2, DS7400XIVER4+, DS7400X, DS7400Xi

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D8112G2L, D6112L, D4112L, D6412, D2212, D2112, D2412, D2812, B3512, B5512, B4512, B6512, B8512G, B9512G

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D130, D133, D134, D8129, D8130

Part numbers FPD-7024, D7024, DSS9400, DS9400I, DS9400M

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9447

Part numbers DS7400, DS7400X, DS7420i

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9447, DS9436, D7033, D7036, FMR-7033

Part numbers D7212, D7412, D9112, D9412, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G

When a fire alarm occurs, the control panel activates Relay A (Terminal 6), providing the trigger input to the “Horn” D192C/D192G. The output from Relay A also changes Point 3’s voltage to 5.0 VDC (electrically, an open condition caused by the 2.4 k. resistor), causing an alarm (burg alarm) condition. This activates Relay B (based on the Summary Alarm Relay programming shown above). Relay B provides the trigger voltage for the “Strobe” D192C/D192G. When the Fire Alarm is acknowledged at the command center, power is no longer applied to Relay A causing the horns to silence and returning Point 3 to a normal state of 2.5 VDC. However, Relay B continues to stay activated until alarm memory is cleared at the command center by using Command 4 or entering Passcode + [ESC]. After the Fire Alarm is acknowledged, the command center first scrolls the fire alarm points, then scrolls AREA 1 1 ALARMS. This occurs because Point 3 is a Burg Point. Once a Command 4 or a Passcode + [ESC] is entered, the Alarm Memory is cleared. Part numbers D192C, D192G, D7212, D7412,D9112, D9124, D9412, D7212G, D7412G, D9112G, D9124G, D9412G

Part numbers D9124, D9100, D9142, D9142F, D9124G, D914GV2

Part numbers D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9465I, MX465, D7035, D7053

Part numbers D7412G, D7212, D7412, D9112, D9124, D9412, D9412G, D192C, D192G, MDL, MDLW, D411, D412, AVS-44, AVS-44R

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4, DS7447

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2,