Bosch Building Technologies

    Showing results for 
    Search instead for 
    Did you mean: 
    Sort by:
    ‎01-19-2024 01:25 PM
    In the controller history, you can see entry as detailed below, showing Detector -On- 14 , what does this indicate?
    View full article
    100% helpful (1/1)
    ‎01-19-2024 01:17 PM
    The following steps describe an efficient way to update the panel firmware in an AVENAR panel 4.x network via SD card, thus keeping downtime of the panels to a minimum. To further reduce downtime, it is recommended to network the panel nodes via ETH.
    View full article
    ‎10-31-2023 09:36 AM
    This article provides instructions for troubleshooting Ground Fault in the FPD-7024 or D7024
    View full article
    ‎05-17-2022 09:14 AM
    How to interpret DBL when displayed on the FPD-7024 or D7024.
    View full article
    ‎05-02-2023 10:43 AM
    This article describes how to capture the panel/ controller communication log when requested by Technical support.
    View full article
    ‎05-02-2023 10:08 AM
    Panel controller displays can become de-calibrated, e.g. upon initial power-up followed by unintentional contact with the display or inaccurately touching the crosshairs.  It becomes noticeable after the panel controller has re-booted and does not respond properly to touch.
    View full article
    ‎04-14-2022 05:08 PM
    This article explains how you can reset the FPA-1000, FPA-1000-UL, and FPA-1000-V2 panels.
    View full article
    ‎06-15-2022 06:36 PM
    Follow the steps from this article to configure FPD-7024 to communicate using Cellular or Ethernet network communications. How to configure the FPD-7024 for network communications using keypad programming.
    View full article
    ‎06-15-2022 04:16 PM
    Follow the steps from this article to access the Point Description programming.
    View full article
    ‎02-16-2022 04:49 PM
    The controller is showing faults but when you access the faults option no errors/fault messages are shown, message 'no suitable element' is shown. Why?
    View full article
    ‎10-25-2021 01:49 PM
    The operator 10000 is shown when detector fault/ Fire is acknowledged on the controller when no operator is logged in (e.g. Operator 2), by pressing the Acknowledge button.
    View full article
    ‎10-25-2021 01:42 PM
    Find out in this article how many Remote Keypads can be set as automatic connection to one Controller (Bosch Fire Alarm Systems)
    View full article
    ‎10-25-2021 12:22 PM
    This article explains why the fire status display of the controller does not show all fire detectors in fire condition.
    View full article
    ‎09-14-2021 09:49 AM
    A sticker on the front of the B450 indicates proper switch positions for selecting various SDI or Option Bus addresses (see figure 1). Figure 1 Sticker with address configurations   There are 2 types of FPD-7024 panels. It must first be determined which is in use before selecting the B450 address: Newer types with firmware version 1.06 and higher. These types are identified by icons on the keypad instead of words (see figure 2). Older types with firmware version 1.03 and lower. These types are identified by words on the keypad. Figure 2 Version 1.06 with Icons vs 1.03 with words   Version 1.06 & newer types: When used as sole communicator or backup to phone line, set the address wheel at 9 for Option Bus address 250. When used as backup to a primary network communicator, set the address wheel at 6 for Option Bus address 134. RPS connections require Option Bus address 250. Be sure the address wheel is set at 9 on the network communicator intended for RPS connections (Ethernet is preferred when allowed). Version 1.03 and older types: Use Option Bus address 250. Only one network communicator is available on these panel types.
    View full article
    ‎05-19-2022 09:40 AM
      Part nummbers - FPE-1000-NE, FPE-1000-NF, FPE-1000-NW, FPA-1000-V2, FPA-1000  
    View full article
    ‎05-19-2022 09:36 AM
    FPA-1000, FPA-1000-V2, FPE-1000-NE, FPE-1000-NF, FPE-1000-NW
    View full article
    ‎05-17-2022 09:39 AM
    How to use the DX4010V2 for connecting to the FPD-7024 with RPS. How to correct the FPD-7024 indicating Trouble Missing DX4020 or DX4010V2.  
    View full article
    ‎05-20-2022 02:37 PM
    Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400
    View full article
    ‎05-20-2022 02:39 PM
    Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9447, D7033, FMR-7033
    View full article
    ‎05-20-2022 02:42 PM
    Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M
    View full article