Bosch Building Technologies

    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎06-17-2018 09:35 PM
    Issue User has authority in all areas but when presses Command 80, Command Center gives error tone and says Area 1 Ok for all on. Solution CMD 80 (All Areas On) and CMD 81 (All Areas Off) must be enabled in programming in order to function. 1)  Using Remote Programming: Go to Panel Wide Parameters; Global Open Close Options; Arming Options and find Enable Cmd 80 - All Areas All On, and Enable Cmd 81 - All Areas All Off and set both to Yes. 2)  Using Keypad Programming: Go to Nibble 1259 and enter 12 to enable both CMD 80 and CMD 81. Part numbers D4412, D6412, D625, D623
    View full article
    ‎06-15-2018 08:21 PM
    How to use the Sensor Trouble Monitor in the D4412 or D6412.
    View full article
    ‎06-15-2018 06:56 PM
    D4412 & D6412
    View full article
    ‎06-15-2018 06:29 PM
    Overview Set up of a D6112 panel to have keyswitch arming. D611 is required. *Note -   D611 is no longermade. Issue Keyswitch arming the D6112 panel. Solution D6112 panel can use a D611 Key Switch Module. The D611 connects to the panels serial device data wiring. (connects in series like a keypad) Panel programming: 4.1 Device#     =    location in the series wiring of the serialdevice data                               1,2,3,4. 4.2 D#Model   =   1 6.1 Combo3    =   8 Notes D4112, D6112, and the D611 no longer made.
    View full article
    ‎06-15-2018 06:13 PM
    Issue Can I mix Heat Detectors and 2 wire smokes with a sounder when using a D132A Smoke Detector Polarity Reversing Module? Solution No. When a Heat detector goes into alarm it puts a short on the input zone to indicate the alarm. The D132A uses Aux power from the panel when the polarity reversal takes place and since a heat detector does not reset when polarity is reversed, it would put a direct short on the Aux power of the panel. Consequently everything connected to the same Aux power terminals would not function.
    View full article
    ‎06-15-2018 03:10 PM
    Issue What keypads will work on the D6112?   Solution   Compatible keypads are: D420A, 6 zone LED. This will work but only the first six zones will be displayed. D620, 8 zone LED. D626, 16 zone LED. D630, 8 zone LED with 3 onboard expansion points. D636A, 16 zone alpha display with 3 onboard expansion points
    View full article
    ‎06-15-2018 02:13 PM
    How to correct the D132A supervision point not showing normal circuit status.  Cannot get the onboard point from the D132A module to show normal circuit status. D132A,D4412,D6412,DS7220,DS7240,D2212
    View full article
    ‎06-14-2018 05:06 PM
    Zone Doubling for Onboard Points 2-8 on D4412 & D6412 Panels
    View full article
    ‎06-14-2018 03:06 PM
    How to enable phone line supervision in the D4412 or D6412.
    View full article
    ‎06-14-2018 02:10 PM
    How to correct working points showing not programmed in RPS diagnostics.
    View full article
    ‎06-13-2018 08:28 PM
    How to control Disarm Authority in the D6412/D4412.
    View full article
    ‎06-13-2018 04:50 PM
    How to enable the Ground Fault display and trouble tone on the D6412/D4412.
    View full article
    ‎06-13-2018 02:48 PM
    How do I change the test report time of a D4112 and a D6112? D6112,D4112,D5200
    View full article
    ‎06-11-2018 08:26 PM
    How to correct when the D4412/D6412 goes into Entry Delay when arming Part-On.
    View full article
    ‎06-08-2018 08:00 PM
    How to lock access to the panel program to prevent take overs. D9112B1, D2012, D2112, D2212, D2412, D2812, D7212B, D7212B1, D8112G2L, D9112, D9112B, D9112B1
    View full article
    ‎06-08-2018 07:12 PM
    How to Part Arm or Part 2 arm the D4412 or D6412.
    View full article
    ‎06-06-2018 09:47 PM
    How to disable reporting on a D4412/6412
    View full article
    ‎06-06-2018 08:08 PM
    How to be sure the monitoring station gets an Alarm Report when testing the D4412 or D6412.
    View full article
    ‎06-06-2018 06:39 PM
    How to test the RF280THS wireless smoke used on the D4412 and D6412. When testing the RF280THS by pressing the 'Test' button does not generate a panel alarm.
    View full article
    ‎06-05-2018 06:49 PM
    How to interpret the message: Missing SDI Device Addresses 150 and 151.
    View full article