Security: Intrusion

Issue What are the enviromental considerations for the proper operation of the Bosch control/communicators? Solution Indoor Dry.   Relative Humidity 5% to 85% noncondensing at +86 degrees Fahrenheit (+30 degrees Celsius). Operating temperature would be +32 degrees Fahrenheit to +120 degrees Fahrenheit ( 0 degrees Celsius to 49 degrees Celsius ).

How to correct the error: RS Control Certificate Not Valid. ITS-DX4020-G, DX4020, B420, RPS, Certificate Builder, RS Control iApp

How to troubleshoot the RS Control app display System is Disabled.

How to select the correct legacy mode or datagram setting for network communications.

How to correct the Panel reporting 'Service Phone Line' when programmed as Local.

How to interpret the 'Check Device' display on a D1255 or D1260 keypad. Why does the keypad display "Check Device"? How to locate which point generated the 'Check Device' display and modify programming to prevent the display.

How to configure Remote Security Control to work withcompatible alarm panels.

  Does Max Number of B208 Limit the number of B308's that can be used?  Or, Does Max Number of B308s Limit the number of B208 's that can be used?  No. The maximum number of B208 modules and B308 modules that are available to the panel type can be connected at one time. The only limit would be available power and SDI2 cable distance specifications which are detailed in the module documentation as well as the panel Installation and System Reference Guide (ISRG).

 The B-Series panel onboard relay can be configured for either: Aux Power Common output Standard Form-C relay Aux Power configuration, Right two pins covered, the C terminal has 12Vdc available and upon activation will switch to the NO terminal.  Relay A turned off, NO to Common reads 0Vdc. Relay A turned on, NO to Common reads +12Vdc. Aux Common configuration,  Left two pins covered, the C terminal is Common.  Upon activation Common is switched to the NO terminal. Relay A turned off, NO to Aux= 0Vdc Relay A turned on, NO to Aux= 12Vdc Dry Contact Configuration No jumper used, NO and C and NC works as a standard dry contact.   Relay A turned off, NO to C= Open, NC to C= Short Relay A turned on, NO to C= Short, NC to C= Open      

How to work with points programmed with Relay Response 1 or Output Response 2.

How to address SDI2 devices without causing address conflicts. Can different types of SDI2 devices use the same address setting? B810, RFRP-A, B820, B208, B308, B420, B426, B520, B920, B921C, B930, B942.

How to determine the max Number of B208 Limit the number of B308's that can be used.  Does Max Number of B208 Limit the number of B308's that can be used?

How to determine how many network interfaces can be added to the control panel. B420 B426 DX4020

How to correct the RS Control APP message:  "System is Disabled".

How to view the panel type and firmware revision.

D5200 Programmer:  The D5200 needs to match a Data Lock code in the panel to access programming. Changing the panel Data Lock Code from the default of 12345 will prevent access. Remote Programming Software: RPS also needs to match the Data Lock code in the panel to access programming.  Changing the panel Data Lock Code from the default of 12345 will prevent access. RPS also needs to match the RPS Passcode (or RAM Passcode in legacy types) in order to allow access programming. Changing the default from 999999 will block RPS access.

How to prevent generating a Fail To Close when Perimeter Arming during the Closing Window. Why does the panel generate a Fail To Close after Perimeter Arming During Closing Window?

The door controlled by the door control module doesn't remain released when the REX sensor configured as 'resettable' continues to detect motion.  B901, D9210C, D9210B,DS150I,DS151I,DS160, DS161

How to program the panel to auto arm at the end of a closing window.