Security: Intrusion

How to adjust the display on the D1260 Command Center. The The [99 + Enter “Setup?” Function] is no longer available in GV2 and higher control panels.

How to determine which wireless interface to use with the EN1224-ON keyfob. How to determine which control panels the EN1224-ON keyfob can be used with. Is the EN1224-ON compatible with D7212 panel types (G, GV2, GV3 or GV4)?

How to activate multiple auxiliary relays on Area Wide or Panel Wide Events.  Programming Area Wide or Panel Wide Relays will only allow a single relay entry.  Use an auxiliary relay such as the D130, D133 or D134 when multiple relays are needed to energize on a panel event.

How to configure Intrusion panel door control for multiple users and access doors

How to use the G Series Battery supervision and Discharge - Recharge Schedule.

How to configure door control in intrusion panels.

How to configure a DX4020 for use with RPS.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

The B8512 or B9512 supervises keypads even when disabled Related Products B8512 B9512 B915 B920 B921C B925F  B926F B930 B942    Overview   Issue The B8512 or B9512 supervises keypads even when Supervision=NO   Solution    If the keypad Type is set to an SDI type keypad (see below) the supervision setting can be configured YES or NO.  When the keypad Type is set to one of the SDI2 type keypads the supervision Yes/No setting is ignored and the keypad is supervised.   SDI2 devices are always supervised by design regardless of the supervision setting.   SDI Keypads  SDI2 Keypads  D1255 VFD Keypad (SDI)  B915  D125xRB Keypad (SDI)  B920  D126x LCD Keypad (SDI)  B921C    B925F    B926F    B930    B942 Notes SDI2 devices that are the same type of device must use different addresses. SDI2 devices that are not the same type can be configured to the same address.  For example: The B915, B92x, B930 or B942 are all same device types (keypads) and must use different addresses. The B920, B208 and B520 are all different device types and can all use the same address.

Cannot silence an alarm when using the Custom Function set to Disarm Related Products B3512 B4512 B5512 B6512 B8512G B9512G D7412GV4 Ver2+ D9412GV4 Ver2+

Issue The FA113 will not arm the panel if it was disarmed from the keypad and will not disarm if panel was armed from the keypad Solution Used as an arm/disarm device, the FA113 is configured to panel zone 74 or 194. Pressing the FA113 Off button sends an OPEN signal to the control panel and pressing the On button sends a NORMAL signal to the control panel. The area should be both Armed and Disarmed by the FA113 for it to function correctly. When the arming state is changed by the FA113, then by another means, the FA113 becomes unable to detect the current armed state of the area and will not respond to the keys pressed. Correct settings for FA113: The transition of the state of point 74 is what causes the area to arm or disarm. • Mode in the D8125INV is set to 4. • Keyswitch Maintained point (Point Type 4) with  Point Response 2, is  required for  the FA113. • Area will arm with a transition from open to normal on point 74. • Area will disarm with a transition from normal to open on point 74. The FA113 is also used for panic on point 75 (7412G) and point 195 (9412G).

Describes how to setup when a valid token is presented at the reader, the alarm system should disarm, and when the door is closed the alarm system should rearm itself.

Describes how to print panel information.