Security: Intrusion

There are 2 tests performed on the FA206i, Walk Test and Transmission Test. Walk Test: With cover in place, quickly (less than 1/2 second) pass a magnet near the Test Mode reed switch. This will activate a 1 minute walk test mode where the LED will light with each trip but no alarm signals will be transmitted. Transmission Test: With cover in place, hold a magnet near the Test Mode reed switch for at least one second. This will activate a one minute transmission test mode where the device will transmit alarm and restoral cycles at regular intervals for 1 minute. Note:  The FA206i LED only lights when in test mode.

Issue What is the Bosch part number for the Inovonics FA206DS wireless motion detector?   Solution   The Bosch part number for the FA206DS would be the DS775RF and is used with the Inovonics FA400 receiver and the Bosch D8125INV wireless interface for Bosch D7412G/D9412G control panels.

How to find a mounting bracket part number for the DS775I. DS775,MX775i.

Issue Does Bosch make a mounting bracket for the DS775I?   Solution   Yes: B335 = Low profile mount bracket B328 = Gimbal mount bracket B338 = Ceiling mount bracket

How to determine the part number for the DS934 long range mirror.

How to determine part numbers for optional lenses for the DS794Z

How to determine which lens to use for the DS915.

How to adjust the sensitivity on the DS937 Motion Detector.

How to set the OD850 to OR Mode.

Issue What would cause the LED to flash? Solution Here is a list of possible reasons for the DS774Z Red LED to flash. Flashing 2 times is a Motion Monitor Timeout Flashing 3 times  Antimask Detection Flashing 4 times  PIR Self test failure Flashing 5  times Low Input Power or Relay Failure          

Issue The DS160/161 fails to operate after multiple trips or cycles. Solution Cause: Possible wrong part (Op- Amp) There are some problems withLot #'s 578C, 579C, 580C with the DS160/161. The DS160/161 could stop detecting after multiple activation, and will not work. Send the customer an advance replacement. Anything passed Lot 580C should have the fix Not all DS160/161 are a problem.

Issue What does it mean when the LED flashes on the motion (PIR)?   Solution   LED                                    Cause On                                      Unit Alarm or Stored Alarm Flashing 2                           Motion Monitor Timeout Flashing 3                           Antimask Detection Flashing 4                           PIR Self test Failure Flashing 5                           Low Input Power or Relay Failure

Issue DS936 motion is causing an alarm when it is not seeing motion.   Solution   On the older version of this motion there will be a bank of DIP switches with four switches.  Set the relay #4 to OFF for NC Alarm Relay Operation.        

Issue What are the dip switch settings for sensitivity adjustments on the DS794Z? Solution The DS794Z comes in 2 versions, one of which has a bank of 5 Configuration switches and an older version that has a bank of 8 Configuration switches. *Bank of 5 Configuration switches Switch 2 On, 3 On= Standard Sensitivity Switch 2 Off, 3 On= Intermediate Sensitivity Switch 2 On, 3 Off= High Sensitivity   **Bank of 8 Configuration switches Switch 5 On, 6 Off= High Sensitivity Switch 5 Off, 6 On= Intermediate Sensitivity Switch 5 On, 6 On= Standard Sensitivity

The door controlled by the door control module doesn't remain released when the REX sensor configured as 'resettable' continues to detect motion.  B901, D9210C, D9210B,DS150I,DS151I,DS160, DS161

Issue How to setup the DS835 for application containing a pet.   Solution   1. Mount the detector 6.5ft (2M) high and set the PIR angle to -5 degrees. 2. Set the PIR sensitivity for Standard (STD). 3. Mount where the animals can not come within 6ft (1.8M) of the detector by climbing on furniture, boxes or other objects. 4. Do not remove the Look Down lens mask. 5. Do not aim the detector at stairways the animal can climb on.  6. Adjust the microwave range for the minimum acceptable coverage for the room in which the detector is installed.

How to troubleshoot the DS860, DS950, DS970 LED Flashing 4 Times. DS860,DS970,DS950

How to determine if the DS150i requires a jumper for selecting input voltage.

How to program  entry delay for motion detectors with a built in popit.