Security: Intrusion

How to use CMD56 to add user codes to the D4412/D6412. When Using CMD56 to Add Codes, there is no prompt to Add Codes, Only Change Codes.

How to interpret a Battery Low report on the D4412/D6412. What battery voltage will the panel transmit a BATTERY LOW report?

How to view the panel log file using the DS7447 keypad. DS7400X,DS7400,DS7400Xi,DS7400XIVER3+,DS7400XIVER4+,DS7400XIVER2,DS7447I,DS7447E,DS7447

How to disable Call Waiting on D4412/D6412 Panels.

How to correct when keypads Display 'Serial IF Fault'. DS7447E,DS7447,DS7447I,DS7400XIVER3+,DS7400XIVER4+,DS7400Xi,DS7400XIVER2.

How to interpret Missing Command 7 or Command 9. Why are points 72 or 136 showing as MISSING in view point status? Why are points 128 or 248 showing as MISSING in view point status? D7212B,D7212B1,D9112B,D9112B1

How to use the Enter Key Relay function in G series panels.

How to program the 2000 Series for expanded points and configure the B208 device address.

How to use the Sensor Trouble Monitor in the D4412 or D6412.

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7460, DS7465,DS7445, DS7432, DS7457i,DS7460i, DS7461i, DS7465i, D8125MUX, D5060, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G, B600

How to Enable Alarm Verification and how it works.

How to return the DS7140 keypad and all Alpha programming to factory default.

How to transfer text from one DS7140 to another DS7140 on a DS7100.

How to disable reporting in the DS7090 or DS7090i. DS7090,DS7090I,DS7090TM,DS7090TMI

How to determine why the BFSK/Relay or Output selected in Point Assignments, or points configured with Relay Response=2, do not reset as expected.  

How to access programming in the EZ Series if the installer code is lost.

How to configure the 2000 Series to use 4-Wire smokes. D2212,D2412,D2812 D133, D134

Issue When uploading a program with a D5200 from a D8112 I get a message on the D5200 of AUX HAS BAD DATA. Solution This can be caused by one of two things: There is corruption in the AUX part of the program caused by uploading or downloading the control panel using a D5200 and not removing the keypad data wires off of terminals 30 and 31. This can be corrected by first removing the keypad data wires off of terminals 30 and 31 then receiving a copy of the program again if the D5200 still displays AUX HAS BAD DATA in the program go to AUX->ABCD and there will be strange characters in those prompts. Simply clear them out and send the program back to the panel then receive it again the error message should now be gone. The last time the panel was programmed it was programmed with a D5100 programmer. There are prompts in the control panel that can only be seen or programmed by the D5100. The prompts were masked off in the D5200 in order to reduce the amount of errors in programming. This error message would indicate that one of the prompts were set incorrectly when programmed with the D5100. This can be corrected by sending the program back to the control panel the receiving it again this will automatically change those prompts to the correct settings by the D5200 and the error message should no longer be displayed on the D5200. Procedure for sending or receiving the panel program: Connect the D5200 program cable between the D5200 Communicator port and the RJ-11 connector in the upper right corner of the D8112. Select the 8112 handler in the D5200 and press ENTER GROUP. Place the cursor on the correct 8112 version: D8112E, D8112E1, D8112G, D8112G1, D8112G2 or D8112A. Momentarily short Disable Restart (terminal 32) to Common (terminal 29). While the cursor is blinking beside the correct panel version, press RECV(COPY) to receive programming or SEND(LOAD) to send programming to the panel.  If the D5200 programmer has difficulty sending or receiving programming: Try removing serial data connections from the panel. Remove devices from terminals 29-32 by either removing wires from terminals, or remove the terminal strip from the right side of the control panel. Place a momentary short between Disable Restart (terminal 32) and Common (terminal 29). If the terminal strip has been removed, carefully place a jumper wire across the holes where terminal 29 and 32 would be.  If still receiving errors during attempts to copy the D8112: Check the D5200 programmer for adequate free memory and verify the 8112 handler is not corrupted. Turn on the D5200 and enter passcode Press the up arrow until DISK STAT displays and press ENTER GROUP. The following screen will appear: DISKSTAT Current Disk: A SizeKilobytes: 512 FreeKilobytes: XXX The number by “FreeKilobytes” should be 60K or greater to effectively operate the D5200.  Less than 60K could result in erratic operation of the programmer and possible corruption of panel programming. Check for corrupted handler:       Place the cursor on the panel type (8112E, 8112E1, 8112G, 8112G1, 8112G2 or 8112A) and press ENTER GROUP. Continue pressing ENTER GROUP on several levels of the program. If the message "BAD DATABASE FILE" appears, the 8112 handler is corrupted. Delete the 8112 handler immediately and use the update feature to obtain a new copy.

How to enable phone line supervision in the D4412 or D6412.

How to Correct the panel sending point restorals but not sending alarms.