Security: Intrusion

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, D1255, D1260, D1265

How to determine the max available current for point 1 in the D4412 or D6412.

Issue Why does the zone light on the D360 Command Center light when the D279A is disarmed? Solution The D8112 panel is programmed with a zone code of 3271 on a particular zone. The purple jumper on the D279A is cut. As a result, the D360 zone light illuminates when the D279A is disarmed. This is normal and will not impact the D8112 arming process.  If the D1252A is used, the disarm state of the D279A is not indicated.

Overview: Power up charging status of the battey on a D4112 panel will send a trouble Zn 9 during Recharge cycle. Issue Why does the panel send a Trouble Zn 9 when the battery is charging?   Solution   After the AC is restored the battery will begin to charge.  When the battery reaches a charging level of 11.1 volts, and maintains battery voltage level above 10.3 volts for 1 minute, the panel will RESET and a battery trouble (Trouble Zn 9) will be sent to the Central Station.  When the battery reaches the charging level of 12.5 volts a Restoral Zn 9 is sent to the Central Station.    

Issue Will the D7112 support a daily 12:00 AM timer test ? Solution Not recommended. If the daily test timer is set for midnight ( 12:00 A.M. ) the panel stops reporting the daily test on January 1st.

Issue When do the D7112 Transmitters send a Low Battery Report? Solution For the Transmitters that use the 3.6V Lithium battery (D7121, D7122, D7130, D7131, D7198, and D7199), the low battery threshold is 3.4V.   For the transmitters that use the 9V Alkaline battery (D7190, D7191), the low battery threshold is 7.2V.

Issue Panel is not sending restorals when the point restores.  Log also has no entries for restorals on the point.   Solution   This is normal if the panel is programmed not to send restorals. In RAM/RPS check in the following: Point Index Codes > Point Indexes 1-16 or Point Indexes 17-31 Disable Restorals Default: No    Selections: Yes or No Yes: Disable restoral reports for this point. No: Enable restoral reports for this point. When this option is enabled, a restoral report is sent to the receiver when the point returns to normal after being in an alarm or trouble condition. If you are using the 5200: In the 5200 check under: 9112B > Point Index > Point Index # (where # is a value between 1 and 31 only) press the white ENTER key press the down arrow key (red keys on the 5200) Repeat until you are at P## Disable Restorals Default: No Selection: Yes or No Yes = Disable Restoralreports for this point. No =  Enable Restoralreports for this point. When this option is enabled, a Restoral report is sent to the receiver when the point returns to normal after being in an alarm or trouble condition. Use this item to automatically put this point back into the system.

Issue When looking at the history log on a D6412 or D4412, the history log displays user 255 key-switch, and the key-switch zone has not been enabled. Solution When arming with command 1, or pressing the all on key, and not using a pass code, "user 255 key-switch arming" will appear in the history log as the user that armed the system.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, 

  How to determine the zone code used on a 2000 Series panel for a D132A trouble point. D132A,D2412,D2812,D2212  

  How to progrma the 6112/5503 to send reboot reports. 6112/5503panel is communicating alarm and trouble signals but, when I do a disable restart it will not send the reboot signal.  

How to interpret the flashing amber circle on an Easy Series control panel.

How to correct the inability to view troubles by pressing the 4-key on 2000 series panels.

How to troubleshoot a faulted panel zone that monitors D125B 2-wire loops. D9112, D9412 D7212B, D7212B1, D9112B, D9112B1  D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2   D8124 D125B 5924 (Honeywell 9124) 5505 5800, 5800B1, 5800C, 5800G 5900, 5900B, 5900B1, 5900C, 5900G   

Issue What brand of 2 wire smokes will work with the Easy Series panel, and how many can be applied to the loop? Solution Radionics/DS D285TH MB2W, MB2WL, D287, D288 = 20 D263 = 20 D263 = 20 D263C = 20 D263S = 20 D263TH = 20 D263THC = 20 D265AW D250AW = 12 D286 MB2W, MB2WL, D287, D288 = 20 D603 MB2W, MB2WL = 20 D604 MB2W, MB2WL = 20 D605 MB2W, MB2WL = 20 DS260 MB2W, MB2WL, D287, D288 = 20 DS230 MB2W, MB2WL = 20 DS230F MB2W, MB2WL = 20 DS233F MB2W, MB2WL = 20 DS250 MB2W, MB2WL, D287, D288 = 20 DS250TH MB2W, MB2WL, D287, D288 = 20 DS260 MB2W, MB2WL, D287, D288 = 20 DS282 = 20 DS282C = 20 DS282S = 20 DS282TH = 20 DS282THS = 20   Bosch Security Systems F220P/PTH F220-B6, -B6C, -B6E, -B6R = 20 1151 B110LP = 15 1451 B401B = 15 2151 B110LP = 15 2400 N/A = 15   System Sensor 2400TH = 15 2451 B401B = 15 2451TH B401B  = 15

Issue What is the difference between the D133 an D134? Solution The D133 has a single relay rated at 2A @ 30 VDC – 0.6A @ 125 VAC. The D134 has two relays rated at 2A @ 30 VDC – 0.6A @ 125 VAC. Current draw for the Relay is 40 mA per relay when activated.

How to make a relay trip when a point is faulted. How to use Relay Follow Point, Output Response type or Relay Response Type.

How to troubleshoot why the FA113 arm/disarm keyfob generates a RF Low Battery Response on the panel keypad. How to troubleshoot the FA113 generating a RF Low Battery Response on the panel keypad. When pressing both Star keys on the FA113 generates Servc RF Low Battery response on Command Center.