Fire

Issue Can the points, outputs and dialer be enabled and disabled from RPS? Solution No, This can only be done from the panel or a keypad attached to the panel. If any of the hard wire points are disabled then follow the steps below to enable points 1-8. Mux points 9 - 255 can be enabled using the "all" command if points 1 - 8 are enabled individually first. To Enable Points Press the Disable Button on the keypad. Press 2 Enable Press 1 Inputs Press 2 Individual Enter the point # (001 - 255) follow by # Repeat steps 3 – 5 until Points 1 -8 are enabled Press 1 Inputs Press 1 All Press the * Clear Button 4 times Follow the steps as above to enable Dialer - NAC's and Relays.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, FPD-7024, D7024, DS9400, DS9400I, DS9400M, D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2

Part numbers D8024, D9061, D9051, D9052

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M,D7052, MX363, DS9460

Part numbers FMR-7033, D7033, DS9447

Part numbers D7024, DS9400, DS9400I, DS9400M, DS9447, DS9436, D7033, D7036, FMR-7033

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers D10024A, D10024, D9024, D8024

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9447, D7033, FMR-7033, FPP-RNAC-8A-4C, D7038, DS9484

Part Numbers D9068, DS9602, DCT-1, DCT-1E, FPT-DACT, D6500

Part numbers SecurComm Modem, StarComm Modem, FPD-7024, D7024, DS9400, DS9400I, DS9400M, RPS, D5500CU

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7460, DS7465,DS745, DS7432, DS7457i,DS7460i, DS7461i, DS7465i, D8125MUX, , D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G, B600

Part numbers D7212, D7412, D9112, D9412, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4,

Issue What could be the cause when adding four System Sensor Horn / Strobes to a Wheelock audio visual loop, and the horns are worrking fine but the strobes are not flashing correctly. Solution When installing Audio / Visual Appliances, all devices on the loop must be from the same manufacturer. Mixing System Sensor with Wheelock or Gentex or any combination may cause the Horns or the Strobes to work intermittently or not at all. This is because each manufacturer has their own Sync Pulse Protocol to run their notification devices.

Part numbers D7022, DS9422

Part numbers D2071A, DS9471, 911A, 911AC, D2071AC, D2071AHC, D2071ACPL-1, D2071ACT, D2071AH

Part numbers D10024A, D10024, D9024, D8024, D328A

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9447

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D130, D133, D134, D8129, D8130