Security: Intrusion

Issue User has authority in all areas but when presses Command 80, Command Center gives error tone and says Area 1 Ok for all on. Solution CMD 80 (All Areas On) and CMD 81 (All Areas Off) must be enabled in programming in order to function. 1)  Using Remote Programming: Go to Panel Wide Parameters; Global Open Close Options; Arming Options and find Enable Cmd 80 - All Areas All On, and Enable Cmd 81 - All Areas All Off and set both to Yes. 2)  Using Keypad Programming: Go to Nibble 1259 and enter 12 to enable both CMD 80 and CMD 81. Part numbers D4412, D6412, D625, D623

How to use the Sensor Trouble Monitor in the D4412 or D6412.

D4412 & D6412

Overview Set up of a D6112 panel to have keyswitch arming. D611 is required. *Note -   D611 is no longermade. Issue Keyswitch arming the D6112 panel. Solution D6112 panel can use a D611 Key Switch Module. The D611 connects to the panels serial device data wiring. (connects in series like a keypad) Panel programming: 4.1 Device#     =    location in the series wiring of the serialdevice data                               1,2,3,4. 4.2 D#Model   =   1 6.1 Combo3    =   8 Notes D4112, D6112, and the D611 no longer made.

Issue Can I mix Heat Detectors and 2 wire smokes with a sounder when using a D132A Smoke Detector Polarity Reversing Module? Solution No. When a Heat detector goes into alarm it puts a short on the input zone to indicate the alarm. The D132A uses Aux power from the panel when the polarity reversal takes place and since a heat detector does not reset when polarity is reversed, it would put a direct short on the Aux power of the panel. Consequently everything connected to the same Aux power terminals would not function.

Issue What keypads will work on the D6112?   Solution   Compatible keypads are: D420A, 6 zone LED. This will work but only the first six zones will be displayed. D620, 8 zone LED. D626, 16 zone LED. D630, 8 zone LED with 3 onboard expansion points. D636A, 16 zone alpha display with 3 onboard expansion points

How to correct the D132A supervision point not showing normal circuit status.  Cannot get the onboard point from the D132A module to show normal circuit status. D132A,D4412,D6412,DS7220,DS7240,D2212

Zone Doubling for Onboard Points 2-8 on D4412 & D6412 Panels

How to enable phone line supervision in the D4412 or D6412.

How to correct working points showing not programmed in RPS diagnostics.

How to control Disarm Authority in the D6412/D4412.

How to enable the Ground Fault display and trouble tone on the D6412/D4412.

How to correct when the D4412/D6412 goes into Entry Delay when arming Part-On.

How to lock access to the panel program to prevent take overs. D9112B1, D2012, D2112, D2212, D2412, D2812, D7212B, D7212B1, D8112G2L, D9112, D9112B, D9112B1

How to Part Arm or Part 2 arm the D4412 or D6412.

How to disable reporting on a D4412/6412

How to be sure the monitoring station gets an Alarm Report when testing the D4412 or D6412.

How to test the RF280THS wireless smoke used on the D4412 and D6412. When testing the RF280THS by pressing the 'Test' button does not generate a panel alarm.

How to configure the D4412 or D6412 for Point Expansion using RPS. 1. Program the D4412 or D6412 for using point doubling. 2.  Address the DX2010 for point groups. 3. Select the EOL to be used with point groups.