Security: Intrusion

Using Menu Shortcuts or Menu Commands on G Series and New G Series panels.

After adding the RFUN-A Universal Transmitter, the point always shows faulted even though it’s normal.

The panel will not send alarm reports and instead is sending an 'ALARM RECENT CLS’ event.

Cannot silence an alarm when using the Custom Function set to Disarm Related Products B3512 B4512 B5512 B6512 B8512G B9512G D7412GV4 Ver2+ D9412GV4 Ver2+

This article explains the proper address selection when connecting the B450 to a Bosch Intrusion Panel. This information is needed to determine which address to select based on panel type, panel firmware revision and if Remote Programming Software will use the B450 to connect to the panel.   Step-by-step guide   Note the sticker on the front of the B450 which indicates switch positions for selecting an SDI2, SDI or Option Bus address (see figure 1).   Figure 1 Sticker with address configurations B8512G, B9512G and B-Series types: The B450 is not required when the cellular communicator will be installed in the Mod-1 (lower) plug-in slot. Use the B450 in applications where signal strength is weak at the panel location. Install the B450 in a remote location with stronger signal strength and connect to SDI2. Follow the instructions below for GV4 panel types connecting to SDI2. GV4 Panel Types: SDI2: Only 1 network communicator is allowed on a single address. Use address 1 or 2 as needed to avoid conflicting with another network communicator on the same address. Connections with Remote Programming Software are available on either address 1 or 2. GV4 or GV3 using SDI: Only 1 network communicator is allowed on a single address. Use address 88 or 92 as needed to avoid conflicting with another network communicator on the same address. When used as sole communicator or as back-up communicator to Phone line, use address 4 for SDI address 88. When used as back-up communicator to Ethernet (B426) use address 5 for SDI address 92, unless the B450 will be used for RPS connections (see note 4 below). Note that SDI address 88 is required for connecting to Remote Programming Software (Ethernet is preferred when allowed). GV2 v7.06+ Panel Types (SDI only): Use address 4 for SDI address 88.

The B8512 or B9512 supervises keypads even when Supervision=NO Related Products B8512 B9512 B915 B920 B921C B925F  B926F B930 B942

The B8512 or B9512 supervises keypads even when disabled Related Products B8512 B9512 B915 B920 B921C B925F  B926F B930 B942    Overview   Issue The B8512 or B9512 supervises keypads even when Supervision=NO   Solution    If the keypad Type is set to an SDI type keypad (see below) the supervision setting can be configured YES or NO.  When the keypad Type is set to one of the SDI2 type keypads the supervision Yes/No setting is ignored and the keypad is supervised.   SDI2 devices are always supervised by design regardless of the supervision setting.   SDI Keypads  SDI2 Keypads  D1255 VFD Keypad (SDI)  B915  D125xRB Keypad (SDI)  B920  D126x LCD Keypad (SDI)  B921C    B925F    B926F    B930    B942 Notes SDI2 devices that are the same type of device must use different addresses. SDI2 devices that are not the same type can be configured to the same address.  For example: The B915, B92x, B930 or B942 are all same device types (keypads) and must use different addresses. The B920, B208 and B520 are all different device types and can all use the same address.

How to modify the B465 Network Access Point Name (APN) entry. What APN is used for the Verizon, AT&T, T-Mobile or Rogers network?

How to modify the B450 Network Access Point Name (APN) entry. What APN is used for the Verizon, AT&T, T-Mobile or Rogers network?

The panel is not sending Alarm Reports, instead is sending Alarm Recent Close Reports.

  The Standby (Reset) pin is not locked down. The panel 12V backup battery is low or missing. Using the wrong product handler, for example, using 2112 instead of 2212. Too much Current Draw on panel. Disconnect devices from Aux Power and try again. Noise or interference on the keypad Data Bus. Disconnect all wires on the panel data terminals. Not enough free memory in the D5200 Programmer. There should be 60K free memory. Refer to KB article: How to Operate the D5200 Hand Held Programmer. The 2212 handler may be corrupted in the D5200. Delete the 2212 handler and re-download it. Refer to KB article: How to Operate the D5200 Hand Held Programmer. Low batteries in the D5200. Replace batteries using 4 C cells. Trying to program a panel that is not powered up The programming cord is not securely connected to the panel programming port or may be damaged. The DX4010V2 comes with a cord with a 4-pin Molex connector on one end and phone connector on other end. This cable may work as a substitute.

How to use the G Series Battery supervision and Discharge - Recharge Schedule.

Issue The keypad displays the Access Module Door Point is in trouble. Diagnostics displays the point as missing. Solution T+ (Tamper Input) of the Access Module is an unsupervised input that is normal when open. Upon a short, the Door Point number assigned to the supervised zone of the Access Module is reported as a MISSING PT###.

If you do not know the IP or MAC for the D6682 and are unable to get in to setup with Telnet.

How to work with the D4112 Battery Discharge and Recharge voltage schedule. When does the D4112 send a Trouble Low Battery report to the monitoring station? When does the D4112 send the Low Battery restore report to the monitoring station?

How to work with the D6112 Battery Discharge and Recharge voltage schedule. When does the D6112 report Low Battery? When does the D6112 report Low Battery Restoral?

How to access the Menu keys on the B915 or B926F keypads. How to use Icon buttons on the B915 keypad.