Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎06-01-2018 04:01 PM
    The D4412 and D6412 use the D621, D623 or D625 command centers. Pressing All-On or Part-On on the will arm only the area where the keypad is assigned. Command 50 may be used to move to an area other than the programmed assigned area.  After moving to the selected area, press either All-on or Part-on to arm the area. Command 80 may be used to arm all areas. Command 81 may be used to disarm all areas. Note:  Commands 80 and/or 81 must be enabled by an individual with assigned authorization to perform the function. Use Command 50 to move to another area and arm:  Press [CMD] [5][0] and enter a valid code if required. The keypad will scroll through all available areas. Press the desired area number to move to the area.  Press All-On or Part-On to arm the selected area.  Pressing and holding [CMD] will exit the Command 50 feature returning the keypad to its “home” area. Use Command 80 to arm All Areas: Press [CMD] [8][0] and enter a valid code if required.       Hold down the All On key for 2 sec and it forces all areas to All On.  Use Command 81 to disarm All Areas:  Press [CMD] [8][1] and enter a valid code if required. The keypad will indicate all areas are off.
    View full article
    ‎05-31-2018 10:42 PM
    How to connect to RPS with the modem connected directly to the Panel. How can I connect to a panel with a modem and only 1 phone line?
    View full article
    ‎05-31-2018 08:36 PM
    How to control the D4412 or D6412 Keypad Backlighting.
    View full article
    ‎05-31-2018 04:17 PM
    How to determine the max distance the DX3010 can be remote located from the control panel. The maximum distance that the DX3010 can be remote located from the control panel is determined by whether or not an auxiliary power supply is used to power the DX3010.
    View full article
    ‎05-31-2018 03:44 PM
    How to determine the max distance the DX2010 can be remote located from the control panel. This distance is determined by whether or not the DX2010 is supplying auxiliary power to devices. The DX2010 has the capacity to provide 12 VDC at up to 100 mA from the Aux Output terminals to power external devices such as motion detectors.
    View full article
    ‎05-25-2018 08:28 PM
    What steps are required to set the Time and Date on the D6412 and the D4412 panels D4412,D6412,D623,D625
    View full article
    ‎05-25-2018 08:26 PM
     How are RF points tested on a D6412 or the D4412 Control Panel? D6412,D4412
    View full article
    ‎05-25-2018 08:24 PM
    The keypad says CALL FOR SERVICE. What can be done to review the trouble? D6412,D4412,D623,D625
    View full article
    ‎05-25-2018 05:43 PM
    How to force Remote Programming Software (RPS) to connect to the panel from a keypad. Remote Programming Software, Answer, 2000 series, D2212, D2412, D2812, D4412, D6412
    View full article
    ‎05-25-2018 04:37 PM
    How to correct Perimeter Instant Points going into Entry/Exit delay on the D4412 or D6412. Why faulting a Perimeter Instant point may go into a delay countdown when the area is armed.
    View full article
    ‎05-24-2018 09:46 PM
    How to address the DX3010 for different off board realys.
    View full article
    ‎05-24-2018 08:31 PM
    How to correct the D6412/D4412 keypad display: System Busy
    View full article
    ‎05-24-2018 08:21 PM
    Can the keypad sounder be adjusted D4412,D621,D623,D625,D6412
    View full article
    ‎05-24-2018 07:58 PM
    How can the trouble condition be displayed on the keypad? D4412,D6412,D623,D625
    View full article
    ‎05-24-2018 04:11 PM
    How many points can the RF3226 receiver handle on a D6412 panel? D6412,RF3226
    View full article
    ‎05-24-2018 04:06 PM
    How are the sounder and display levels adjusted on the D623 and D625 Keypads? D6412,D623,D625,D4412
    View full article
    ‎05-24-2018 04:09 PM
    How to use the D4412/D6412 for only Wireless Panic points.   When none of the wireless panics will trip into alarm.   
    View full article
    ‎05-23-2018 09:51 PM
    What are the new part numbers for the D9529 Octal Relay and the D9528 Eight Input device? D6412,D4412,DX2010,DX3010
    View full article
    ‎05-23-2018 08:32 PM
    How to interpret the D6412 or D4412 report: Closing Delinquent Signal.
    View full article
    ‎05-23-2018 08:32 PM
    Why does the central station receiver report incorrect account information from the D4412 or D6412 panel D6412,D4412
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist