Bosch Building Technologies

    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎06-15-2018 08:21 PM
    How to use the Sensor Trouble Monitor in the D4412 or D6412.
    View full article
    ‎06-15-2018 06:56 PM
    D4412 & D6412
    View full article
    ‎06-15-2018 06:29 PM
    Overview Set up of a D6112 panel to have keyswitch arming. D611 is required. *Note -   D611 is no longermade. Issue Keyswitch arming the D6112 panel. Solution D6112 panel can use a D611 Key Switch Module. The D611 connects to the panels serial device data wiring. (connects in series like a keypad) Panel programming: 4.1 Device#     =    location in the series wiring of the serialdevice data                               1,2,3,4. 4.2 D#Model   =   1 6.1 Combo3    =   8 Notes D4112, D6112, and the D611 no longer made.
    View full article
    ‎06-15-2018 06:13 PM
    Issue Can I mix Heat Detectors and 2 wire smokes with a sounder when using a D132A Smoke Detector Polarity Reversing Module? Solution No. When a Heat detector goes into alarm it puts a short on the input zone to indicate the alarm. The D132A uses Aux power from the panel when the polarity reversal takes place and since a heat detector does not reset when polarity is reversed, it would put a direct short on the Aux power of the panel. Consequently everything connected to the same Aux power terminals would not function.
    View full article
    ‎06-15-2018 03:10 PM
    Issue What keypads will work on the D6112?   Solution   Compatible keypads are: D420A, 6 zone LED. This will work but only the first six zones will be displayed. D620, 8 zone LED. D626, 16 zone LED. D630, 8 zone LED with 3 onboard expansion points. D636A, 16 zone alpha display with 3 onboard expansion points
    View full article
    ‎06-15-2018 02:13 PM
    How to correct the D132A supervision point not showing normal circuit status.  Cannot get the onboard point from the D132A module to show normal circuit status. D132A,D4412,D6412,DS7220,DS7240,D2212
    View full article
    ‎06-14-2018 05:06 PM
    Zone Doubling for Onboard Points 2-8 on D4412 & D6412 Panels
    View full article
    ‎06-14-2018 03:06 PM
    How to enable phone line supervision in the D4412 or D6412.
    View full article
    ‎06-14-2018 02:10 PM
    How to correct working points showing not programmed in RPS diagnostics.
    View full article
    ‎06-13-2018 08:28 PM
    How to control Disarm Authority in the D6412/D4412.
    View full article
    ‎06-13-2018 04:50 PM
    How to enable the Ground Fault display and trouble tone on the D6412/D4412.
    View full article
    ‎06-13-2018 02:48 PM
    How do I change the test report time of a D4112 and a D6112? D6112,D4112,D5200
    View full article
    ‎06-11-2018 08:26 PM
    How to correct when the D4412/D6412 goes into Entry Delay when arming Part-On.
    View full article
    ‎06-08-2018 08:00 PM
    How to lock access to the panel program to prevent take overs. D9112B1, D2012, D2112, D2212, D2412, D2812, D7212B, D7212B1, D8112G2L, D9112, D9112B, D9112B1
    View full article
    ‎06-08-2018 07:12 PM
    How to Part Arm or Part 2 arm the D4412 or D6412.
    View full article
    ‎06-06-2018 09:47 PM
    How to disable reporting on a D4412/6412
    View full article
    ‎06-06-2018 08:08 PM
    How to be sure the monitoring station gets an Alarm Report when testing the D4412 or D6412.
    View full article
    ‎06-06-2018 06:39 PM
    How to test the RF280THS wireless smoke used on the D4412 and D6412. When testing the RF280THS by pressing the 'Test' button does not generate a panel alarm.
    View full article
    ‎06-05-2018 05:50 PM
    How to configure the D4412 or D6412 for Point Expansion using RPS. 1. Program the D4412 or D6412 for using point doubling. 2.  Address the DX2010 for point groups. 3. Select the EOL to be used with point groups.
    View full article
    ‎06-05-2018 06:49 PM
    How to interpret the message: Missing SDI Device Addresses 150 and 151.
    View full article
    Top Contributors