Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎06-25-2018 06:53 PM
    D5200 Programmer:  The D5200 needs to match a Data Lock code in the panel to access programming. Changing the panel Data Lock Code from the default of 12345 will prevent access. Remote Programming Software: RPS also needs to match the Data Lock code in the panel to access programming.  Changing the panel Data Lock Code from the default of 12345 will prevent access. RPS also needs to match the RPS Passcode (or RAM Passcode in legacy types) in order to allow access programming. Changing the default from 999999 will block RPS access.
    View full article
    ‎07-30-2018 07:14 PM
    How to interpret "user 255 key-switch arming" in the D4412/D6412 with no programmed keyswitch zone.
    View full article
    ‎07-11-2018 04:28 PM
     How to enable Open/Close Reports for Part On Modes. The panel sends Open/Close reports for All-On but not for Part-On.
    View full article
    ‎05-25-2018 08:26 PM
     How are RF points tested on a D6412 or the D4412 Control Panel? D6412,D4412
    View full article
    ‎07-30-2018 08:16 PM
    How to add ITI transmitters, are they added in normal or faulted condition? D4412, D6412, RF3226, ITI WIRELESS DEVICES.
    View full article
    ‎08-02-2018 08:33 PM
    Issue How can the rising sun key or trapazoid key be used to activate an output on the D4412/D6412 control communicator?   Solution   Under Output Parameters, program a 1,15 for the trapazoid key or 2,0 for the rising sun key to activate an assigned output when the keyfob's alternate buttons are depressed.        
    View full article
    ‎05-15-2018 04:27 PM
    While inputting an installer passcode number, I'm unable to enter the programming mode. D6412
    View full article
    ‎06-06-2018 06:39 PM
    How to test the RF280THS wireless smoke used on the D4412 and D6412. When testing the RF280THS by pressing the 'Test' button does not generate a panel alarm.
    View full article
    ‎07-10-2018 06:32 PM
    Issue When programming through the keypad, what is the nibble to program the RF receiver?   Solution                                     Nibble 1249                            Values: 0  = no RF receiver connected 1  = RF receiver 1 connected, set to address 50 2  = RF receiver 2 connected, set to address 51 3  = RF receiver 1 and 2 connected
    View full article
    ‎05-23-2018 08:14 PM
    Definition: Watch Mode Only- This point will not create alarm or trouble responses and will not generate reports to the Central Monitoring Station.  Program the Point: Select Point Type= 0. Select all Yes/No options= NO. Set Alarm Report Routing = 0: No Reports, No Events to Log/Printer. Set Restoral Report Routing = 0: No Reports, No Events to Log/Printer. Select Watch Tone and enable Watch Point: Select [Cmd] + 62 to select the watch tone. Select [Cmd] + 63 to select the watch point(s).
    View full article
    ‎07-30-2018 09:53 PM
    How to learn the RF3502 into the panel; as a point or a keyfob assigned to a user? D4412, D6412, RF3224, RF3502
    View full article
    ‎05-24-2018 04:11 PM
    How many points can the RF3226 receiver handle on a D6412 panel? D6412,RF3226
    View full article
    ‎07-27-2018 02:34 PM
    Issue When looking at the history log on a D6412 or D4412, the history log displays user 255 key-switch, and the key-switch zone has not been enabled. Solution When arming with command 1, or pressing the all on key, and not using a pass code, "user 255 key-switch arming" will appear in the history log as the user that armed the system.
    View full article
    ‎05-23-2018 09:51 PM
    What are the new part numbers for the D9529 Octal Relay and the D9528 Eight Input device? D6412,D4412,DX2010,DX3010
    View full article
    ‎07-30-2018 10:36 PM
    How to troubleshoot when the D6412 or D4412 panel will not release the phone line.
    View full article
    ‎07-11-2018 06:05 PM
    Issue What type of RF receivers are compatible with the D4412/D6412? Solution The ITI receiver part number RF3226 and the Bosch receiver part number RF3224.
    View full article
    ‎06-26-2018 02:18 PM
    How to view the panel type and firmware revision.
    View full article
    ‎06-25-2018 04:20 PM
    How to troubleshoot 'Receiver Error' on the D6412 or /D4412 control panel. D4412,D6412,RF3226
    View full article
    ‎07-24-2018 09:09 PM
    How to correct the D4412/D6412 dialing 2 Numbers and disconnecting.
    View full article
    ‎07-17-2018 03:39 PM
    When the "B" key is activated. There is no response at the keypad if programmed for panic.
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist