Security: Intrusion

How to troubleshoot why the D4412/D6412 keypad displays Not Ready regardless of all points normal. D623,D625

Issue The instructions do not show how to interface the D169 to the D6412. Solution Voice Verification: Allows the panel to control a D169 2-way Voice Verification Module. The D169 allows the central station personnel to verify alarms with a two-way voice session with the premises. The premises phone line runs from the panel to the D169 and then to the premises phones. There are two other module connections to the panel: the programmable relay output (-12 VDC) programmed with the Voice Request output function (2,10), and a point (zone) programmed as a Voice Active point. The panel must also have one or more points with the Voice Verification option selected in the point index. When a point with Voice Verification generates an alarm event: The panel transmits the alarm report to the receiver at the central station. When the central station receiver acknowledges the report, the panel activates the Voice Request output function and starts a 30-second report delay time. All reports are delayed. The D169 has 30 seconds to start a two-way voice session. An operator at the central station picks up the phone line from the receiver with a DTMF telephone and presses [2]. At the premises, the D169 picked up the phone line when the panel activated the Voice Request output function. When it hears the DTMF tone from the operator pressing [2], it begins a two-way voice session by first shorting the panel’s Voice Active point. When the Voice Active point is shorted, the panel silences the non-fire alarm output (sets the Bell Timer to zero). Only the user can silence a fire alarm output. As long as the Voice Active point is shorted, the panel continues to keep reports buffered. The D169 ends the voice session by removing the short from the voice active point. The panel resets the bell time and Alarm Event Abort Window (assuming a user at the premises did not change the arming state of the panel during the voice session). Normal reporting (communication) resumes.                    Hardware Configuration 1.) J1 cable to the D6412 Brown to the negative out put Green to the Voice active zone one the panel Blue to the alarm out put if used White not used Red 12volts positive Black panel common 2.) J3 leave a default with A, and D jumped out. Need to follow instruction on the D169 for siren wiring, and operating instructions of the D169.                          

How to correct the D6412/D4412 keypad display: System Busy

   How to delete passcodes from the D4412 or D6412 using the D625 or D623 keypd. D623,D625,D6412,D4412.  

How to interpret the message: Missing SDI Device Addresses 150 and 151.

How to Troubleshoot the D4412/D6412 keypad says Not Programmed, See Install Guide.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G, D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P, D6412, D4412, B3512, B4512, B5512, B6512

D6412, D4412

How to configure the D4412 or D6412 for Point Expansion using Keypad Programming.

How to work with the RF3224 Cover Tamper switch. Can the front spring tamper on the RF3224 wireless receiver be disabled?      

How to set the 4-button RF3334 RF Keyfob Trapazoid or Rising Sun key to activate an output.

How to correct erratic operation of the GE-ITI 60-641 Long Life Door/Window Sensor. 60-641-95 Long-Life D/W Sensor Gray, 60-641-11-95 Long-Life D/W Sensor Brown, D216RF, D208RF, D2412, D4412, D6412, D2212, RF3226, D2812

 How to enable Open/Close Reports for Part On Modes. The panel sends Open/Close reports for All-On but not for Part-On.

How to use the D4412/D6412 for only Wireless Panic points.   When none of the wireless panics will trip into alarm.   

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P, D208RF, D216RF, RF3226

D5200 Programmer:  The D5200 needs to match a Data Lock code in the panel to access programming. Changing the panel Data Lock Code from the default of 12345 will prevent access. Remote Programming Software: RPS also needs to match the Data Lock code in the panel to access programming.  Changing the panel Data Lock Code from the default of 12345 will prevent access. RPS also needs to match the RPS Passcode (or RAM Passcode in legacy types) in order to allow access programming. Changing the default from 999999 will block RPS access.