Security: Intrusion

How to program Passcode Duress on the D7212B,  D7212B1, D9112B or D9112B1

How to interpret the WDSRP log entry: ARMED LEVEL 2 from a DS7060 control panel.

How to view the panel log file using the DS7447 keypad. DS7400X,DS7400,DS7400Xi,DS7400XIVER3+,DS7400XIVER4+,DS7400XIVER2,DS7447I,DS7447E,DS7447

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,

Part numbers D7112, D7125, D7191, D7190

Issue Bell output only activates for 30 seconds even though it is programmed for 99 minutes. Solution When the fire bell time (address 0195 in version 3, address 4032 in version 4) or burglary bell time (address 0196 in version 3, address 4033 in version 4) is set to 99 for a DS7400Xi version 3 or 4 this sets the bell cutoff time to 30 seconds. For indefinite bell output then these programming addresses should be set to 00.  For 98 minutes of bell output these should be set to 98. Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,

Issue What is the dual phone line monitor module for the D7112?   Solution   The D728 would be the dual phone line monitor module for the D7112 panel.

Issue How is the DS7432 eight input remote module interfaced with DS7400 series panels? Solution The DS7432 eight input remote module is interfaced with DS7400 series panels thru either the DS7430 (single mux bus) or DS7436 (dual mux bus) Multiplex Expansion Module. Connect the mux bus + terminal to the DS7432 module bus + and the respective mux bus - terminal to the DS7432 module bus - terminal. DS7432 is powered from Aux power from the DS7400(or X, Xi) panel terminals 7 (aux -) and 8 (aux +).  Connect power to DS7432 Power +, -. Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, Ds7432, DS7430, DS7436

What programmmer was used to program the wireless transmitters point transmission interval, point #, and house code on a D7112 wireless system?

Issue This is a report that is generated when the system is armed and Closing Ring Back is enabled but the closing report is not. The Report 0 occurs because the panel does a phone check to see if dial-tone  is detected. If dial tone is not detected at the time the panel is armed it will display a Communication Fault on the Keypad it will generate this error in the History buffer. How are Report Fail 0 messages prevented? Solution To prevent these errors from occurring perform the following steps: On the DS7400/X version 1.xx 1. Enter in program mode by entering in the program PIN + #0 2. Depress 0011 03# 3. Hold the * key for 3 seconds to exit out of Program mode  On the DS7400Xi  Version 2.xx and Ver 3+ 1. Enter in program mode by entering in the program PIN + #0 2. Press 0000 03# 3. Hold the * key for 3 seconds to exit out of Program mode On the DS7400Xi Ver 4 1. Enter in program mode by entering in the program PIN + #0 2. Press 0000 03# 3. Hold the * key for 3 seconds to exit out of Program mode Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,

Issue 1.) The D7112 receives a busy signal for all ten attempts to reach the receiver. Diagnosis Calls are not reaching the receiver The receiver call load could be too great. Issue 2. )What would cause the receiver to answer the call and provide an acknowledgment tone, but the communicator does not transmit reports? Diagnosis The receiver is not producing the correct acknowledgement tones. The D136 relay in J10 for ground start phone systems is inserted incorrectly. Solution Verify that the correct prefixes and phone numbers for the receiver have been programmed into the D7112. Verify that the phone lines are not shorted between the phone company's equipment and the receiver by placing a call to the number for the receiver. If you hear the line ring, but the ring detector doesn't light, or if you hear a busy signal and the green "on the line" (OL) indicator is not lit, call the phone company for service. Verify that the receiver is producing a 2300 Hz or Modem II acknowledgment tone. Verify the D136 relay is in the socket J10 correctly.  

Issue Unable to use Command 00 function. When CMD 00 is entered, keypad reads 'SYSTEM COMMAND' or 'INVALID KEYS'. Solution Un-Bypassing points on the D7112 panel must be done by using the FUNCTION Menu. Access the Function menu by pressing 'Enter' at the idle disarmed text. Press Next repeatedly until Function Menu displays. To access the UNBYPASS screen press enter on Function menu and Next until UNBYPASS displays. Display will read ENTER POINT NUMBER, enter the point number to be bypassed and press Enter. Display will read the text for the point, press enter again and screen will read POINT UNBYPASSED.

How to transfer text from one DS7140 to another DS7140 on a DS7100.

 Issue Is there a list of commands for the DS panels?   Solution   DS Commands DS7090, DS7090I, and DS7100 Command 1            Arm All Command 2            Instant Arm Command 3            Delay Arm Command 4            Custom Arm Command 5            Custom Arm Command 6            Custom Arm Command 7            Alert Mode (chime mode) Command 9            Zone Bypassing Command 81          Area Test Command 89          History Command 89*        History Reset Command 80          Battery Test Command 82          Communicator Test Command 80          Fire Reset Command 84          Indicator Light and Display Test Command 83          Remote Program Dial Out Command 86          Remote Program Answer Command 85          Siren Test Command 87          Trouble Display Command 87*       Trouble Display Reset

How to to make the DS7220 or DS7240 panel local only.

How to return the DS7060 to factory default.

How to edit phone numbers when not allowed with keypad programming. DS7060, DS7080i,DS7080i, DS7080i v2, DS7080iP32, DS7400, DS7400X, DS7400Xi, DS7447

Panel DS7400Xi

How to make the DS7100 dial without waiting the 7 second delay.

Issue What are the steps on setting the panel time for the DS7100?   Solution   Enter in a valid master code # 0,7 Enter 01, then enter the time ( 24 hr. format ) then #