Security: Intrusion

Issue How can I get the panel to test the bell when the system is Armed? Solution In order to have the bell sound at the end of the Arming Sequence, you must follow the steps listed below: Put the system into program mode by either entering the INSTALLERS (Default is 98765) CODE # 0 or holding down the S1 pin on the middle of the control board down towards the bottom. Type in 81 # and see what the first data digit is and make a note of it. Ex. D1=1. Press # again to see what the second data digit is and make a note of it. Ex. D2=0. Press # again to see what the third data digit is and make a note of it. Ex. D3=7. Press # again to see what the fourth and final data digit is and make a note of it. Ex. D4=6 Ex  D1=1 D2=0 D3=7 D4=6 for a complete number of 1076. In order to have the system do the Bell test when arming you must make digit 2 a 2 or a 3 and the other digits will stay the same. 2 would give you the following: Test Bell but NOT the Phone line upon arming. 3 would give you the following: Test Phone line AND Bell upon arming. Now press the * twice to get you back to the ADR= and do the following: To make the change with the number 2 option you will press 811276# OR To make the change with the number 3 option you will press 811376# After that you can hold * down for 3 seconds, release it, and test the changes out.

Issue D7112 Panel battery will not hold a charge. Solution A slow flashing (1 sec on, 1 sec off) yellow LED with the green CPU LED off indicates a power supply overload condition.  The panel detects the battery as missing and the power supply cannot meet the power demand of the devices on the panel. The panel is shut down.

Issue How does the phone line monitor for the DS7100 operate?   Solution   If the monitor detects a phone line fault for more than 50 seconds, the power LED will begin to flash.  If the audible output has been enabled in line 89, the keypad sounder will pulse every ten seconds if the control is disarmed. If the panel is armed, the siren output will activate. To ascertain if the trouble condition is indeed a phone line failure, enter # 87 at the keypad. The display will indicate "Communication Failure". If the "System Trouble Report" (line 51) is programmed the system will try to send this report. A phone line failure may be caused by: A cut or missing phone line. A reversed connection (Tip, and Ring Reversed) A miswired jack To clear the error; Determine the cause of the failure and eliminate the cause. After eliminating the cause of the failure, wait at least ten seconds. The error will clear if the problem has been eliminated and the LED will stop flashing provided a failure has not occurred on the central station phone numbers. If a failure has occurred at the central station restore by entering # 87 * at the keypad.

How to view System Troubles on the DS7240/DS7220. DS7240,DS7220,DS7445I,DS7447I

How to force the DS7240/DS7220 to answer remote programming software. DS7240,DS7220,DS7445I,DS7447I

Issue How is the phone line monitor turned on or off in programming?   Solution   DS7100 version 5.03 or higher. The phone line monitor feature has been enhanced to provide output to allow enabling or disabling of the featrure through programming and to automatically reset after the phone line is restrored. The feature is controlled in data digit 2 of program address 89. To enable the phone line fault monitor without an audible output, program line 89 as 0200. To enable the phone line fault monitor with a keypad warning beep when the system is disarmed and siren output when the system is armed, program line 89 as 0600. To disable phone line fault monitor program line 89 as 0000.

How to determine how many command centers (keypads) are supported by the D7112. How many command centers can be supported on the D7112?

Issue Multiplex troubles and loss of communication to devices.   Solution   Perform the Following Troubleshooting steps 1. Check the voltage on the Mutilplex Bus 2. If the Voltage is 12VDC 3. Check and make sure the panel is out of programmer’s mode 4. Look for duplicate addresses 5. *Disable Bus lock 6. Make sure 12VDC is not connect to the Multiplex bus If the Voltage is 0 - . 3VDC 1. Check for Shorts on the multiplex loop 2. Check for reverse polarity to devices 3. If the device require diodes make sure the cathode side is on the positive side. * To Disable Bus Lock 1. Enter in to Programmers Mode  by code + #0 2. Type in 9999 *5 Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7430, DS7436

  Issue Symptom The keypad displays Oct. Relay Fault. Probable Cause The octal relay module ( DS7488 ) is defective or the wiring to the module is defective. There is not a DS7488 or a DS7488 has been removed from the system. Solution Check the wiring to the module. Enter the programming mode. This will rescan the options bus and clear the problem. Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,  DS7488

How to View Point Status on the DS7240/DS7220 panels. DS7220,DS7240,DS7447I

Issue Why does an invisible or silent zone activate the alarm output? Solution Probable Cause The output is programmed as "latch on alarm" (0) Possible Solution Program the output to follow zone alarms ( 6 ). Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,

How to determine the number of passcodes are available in the D7112. How many passcodes can the D7112 panel have?

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7447

How to determine the capacity of the D7112 panel event log. How many events are held in the D7112 panel log?

How to view the panel log file using the DS7447 keypad. DS7400X,DS7400,DS7400Xi,DS7400XIVER3+,DS7400XIVER4+,DS7400XIVER2,DS7447I,DS7447E,DS7447