Security: Intrusion

How to interpret panel reports generated by MISSING Point Events on G Series Panels.

How to Enable Alarm Verification and how it works.

How to troubleshoot wrong point text displaying after a fire alarm is silenced on the GV2 panel type using firmware version 7.03 and a D1260 keypad.

Overview When wireless points are faulted, they display as 'Short' to the panel. When the wireless point tamper switch is faulted it will display as an 'Open' to the panel. Issue The panel when using a D8125INV and wireless points shows normal/faulted when point transitions from normal to off normal but the control always shows shorted. Solution Problem may be caused by another point expander connected to the control panel. Remove D8125INV from control panel and determine if points go missing. If points remain active (normal, faulted, etc) the control panel is interfacing with the points through another addressable point expander. Part numbers D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G, D8125INV, ISW-D8125CW, ISW-D8125CW-V2, FA400, EN4200

How to determine why Central Station doesn't receive supervisory events sent with BFSK format. When sending signals using BFSK format, the central station does not receive Supervisory events.

How to determine why the BFSK/Relay or Output selected in Point Assignments, or points configured with Relay Response=2, do not reset as expected.  

Part numbers D7412, D9412, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B6512, B8512G, B9512G, D9210, D9210B, D9210C, B901

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G, D1255, D1255RB, D1255R, D1255W

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4,

How to Correct the panel sending point restorals but not sending alarms.

How to correct the D1255 Command Center going blank while selecting menus. While entering key stroke commands and using the Menu option on the D1255, the display blanks out and the speaker crackles then the display comes up after 5 seconds.

How to configure the DX4020 for Different Ports.

How to correct custom functions that execute when A, B or C keys are pressed on the D720. D1256 Command Center functions are Executing when A, B or C Keys on a D720 are pressed.

How to correct the Central Station not getting BFSK Reports.

How to test the Lithium Battery for proper voltage on 7000/9000, G and GV2 Series Panels.

How to supervise the DX4020 on the SDI bus.

How to correct the D5200 displaying Error: Ram Card Protected.

How to correct points 001-008 reporting in COMEX format as 100-800.