Issue
When programming the D279 keypad point index on the 7000/9000, G, GV2, & GV3 series panels, how should the type and response be programmed?
Solution
Program a type 7 for D279 (O/C Non-Priority): The D279 provides point arming and disarming independent of the area arm state. A non-priority D279 point arm state does not affect the area arm state. Point Response must be programmed 1. Program type 8 for D279 (O/C Priority): The D279 provides point arming and disarming independent of the area arm state. A priority D279 point must be armed before an area can be armed. Program Point Response as 2.
Issue
How far can the D9131A be installed remoted from the control panel?
Solution
The D9131A can be installed a maximum of 1000 ft. (305m) from the panel using 22 AWG solid copper wire.
How to use the D928 Dual Phone Module with PBX and Standard Phone Lines.
Can one of two phone lines be required to dial 9 for outside line (PBX) when the other (standard line) does not?
The keypad will display ‘Command Disabled’ when the Menu key is pressed for one of the following reasons.
If the menu item # 1 in the function list is set with a function 0 and marked yes for any Command Center.
If all of the Functions for the Command Center are selected as No (disabled).
To prevent the keypad from displaying ‘Command Disabled’ after selecting Menu;
Select a non-zero value for the Function # of Menu Item 1.
Ensure that at least one of the Menu Items intended for use are set as Yes.
How long does a keypad message stay on the the keypad when it was sent from RPS or RAM IV Diagnostic Mode?
RPS,D7212,D7212B,D7212G,D7412,D9112,D9112B,D9412,RAMIV,D9412G,D7412G,D9112B1,D7212B1,D7412GV2,D7412GV3,D7412GV4,D7212GV2,D7212GV3,D7212GV4,D9412GV2,D9412GV3,D9412GV4
How to program a shared area and sequence of operation of a shared area in conjunction with two associate areas.
D9412G,D7412G,D7212G,D7212,D7412,D9112,D9412G, D9412GV2,D9412GV3,D9412GV4,D7412GV2, D7412G, D7412GV3, D7412GV4, D7212G, D7212GV2,D7212GV3,D7212GV4
How to determine which points are available for programming using the D8125MUX.
D8125MUX, DS7457, DS7457I, DS7457IF, DS7460, DS7460I, DS7461I, DS7465, DS7465I, DS7052, DS7051, D7050, D7050-BB, MX835, MX934, MX794Z, MX250, MXB2W, D5060.
How do you enable basic Openings and Closing reporting by user on the 7000/9000 series panel?
D9412,D7412,D7212,D9412G,D7412G,D7212G,D9412GV2,D7412GV2,D7212GV2,D9412GV3,D7412GV3,D7212GV3,D9412GV4,D7412GV4,D7212GV4
Program configuration of a DS7432 module on a D8125 Mux system
D9412,D7412,D7212,D9412G,D7412G,D7212G,D9412GV2,D7412GV2,D7212GV2,D9412GV3,D7412GV3,D7212GV3,D9412GV4,D7412GV4,D7212GV4,D8125 MUX
