Security: Intrusion

How to interpret the two alternating asterisks (*) on the D8112 command center. D8112G2,D8112E1,D8112G1,D8112A

How to determine D928 compatibility with D7212 panel types. After changing the setting "Two Phone Lines" to Yes then unlatching and relatching the Reset Pin, it is changed back to No. 

How to correct the D4412/D6412 only reporting to one destination and not following programmed routing.

 How to enable Open/Close Reports for Part On Modes. The panel sends Open/Close reports for All-On but not for Part-On.

How to correct point 1 on a D4412 or D6412 will not restore even when using the programmed EOL. Point 1 on the D4412 or D6412 will not restore even after strapping out with the EOL selected in Global Point Configuration. 

How to correct the Panel reporting Extra Points on Zones 1-8. The keypad is displaying trouble due to extra point on an onboard zone(1-8). 5800C,5800G,5900C,5900G

How to configure Swinger Shunt to prevent points from automatically bypassing after  only 1 alarm. Why does the panel zone generate 1 Alarm and then goes into Swinger Bypass? D4412,D6412,DS7220,DS7240

How to set the 4-button RF3334 RF Keyfob Trapazoid or Rising Sun key to activate an output.

How to correct the RS Control APP message:  "System is Disabled".

How to set the test report time on the 190 Test Report Timer module for the 4012/8012 panel. D4012,D8012

Issue Trouble connecting to the D4412 with RPS / RAM IV using the DX4010i. What dip switches need to be set to make the DX4010i connect to the panel? What type of cable is needed between the DX4010i and the Laptop or PC? Solution RAMIV / RPS needs to be revision 3.6 or higher. Set the address 0 (Installer's mode) Dip Switches 6 and 8 in the off postion on the DX4010i. Use a NULL cable to connect the DX4010i to the Laptop or PC. For remote programming connection, use the RJ-16 to molex connector to the Aux / Data header. Lock the Installer or Reset Pin on the panel. In the RSP/ RAMIV Connection screen change the connection type from MODEM to ENHANCED DIRECT, then click connect. *If connected to a D4412 panel and the address is set wrong on the DX4010i then a message of "INVALID RAM PASSCODE" may be generated.

How to Activate the ALT ALARM RELAY on a D8112 Panel. When is the ALT ALARM RELAY triggered? D8112G2,D8112E1,D8112G1,D8112A

What programmmer was used to program the wireless transmitters point transmission interval, point #, and house code on a D7112 wireless system?

Issue Symptom What would cause the programmer to display ( Plug in 7112) when you press send or receiver Diagnosis The programmer is not correctly connected to the D7112. Solution Verify that the data/power cord is plugged securely in the programmer port J4, on the D7112. Verify that the data/power cord is plugged securely into the communicator port on the D5200 programmer Check each conductor in the data/power cord for continuity Part numbers D7112, D5200

How to access View Point Status in the D4412/D6412. D4412,D6412,D623,D625

Part numbers D2212, D2212B, D2212BE, D2412, D2412U, D2412UE, D2812, D2812U, D2812P, D222A, D223A, D202A, D220A

How to troubleshoot missing onboard points 1-8 on the D4412/D6412.

How to initiate a programmed test time on 2000 Series control panels.  Does the D2212 Timer Test Need to be Initiated from the Keypad? D2812,D220A (8 led),D2412,D2212,D222A LCD,D223A LCD,D220A,D222,D223

How to troubleshoot why Zone Test will not work on a DS7400 Version1 or 2 Panel. DS7400,DS7400X,DS7400XIVER2.

How to troubleshoot why the D4412/D6412 keypad displays Not Ready regardless of all points normal. D623,D625