Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Intrusion

    Sort by:
    ‎07-11-2018 06:39 PM
       How to delete passcodes from the D4412 or D6412 using the D625 or D623 keypd. D623,D625,D6412,D4412.  
    View full article
    ‎07-11-2018 06:38 PM
    1.  Ensure the area is disarmed. 2.  Press Cmd + 4 + 2.  The flashing Cmd light is a prompt to enter a valid passcode.  3.  Enter a valid passcode and the D621 displays system trouble events by lighting the point indicators (zone leds)as described below:  Zone 1 Lit steady = Telephone line Fail  Zone 1 Slow Flash = Comm Fail, Destination 1  Zone 1 Fast Flash = Comm Fail, Destination 2  Zone 2 Lit steady = Alternate Comm Trouble  Zone 3 Lit steady = Installer Switch Closed  Zone 4 Lit steady = Backup Battery low  Zone 4 Lit steady = Slow Flash = Backup Battery Missing  Zone 5 Lit steady = Bell Supervision Fail  Zone 6 Lit steady = RF Receiver Jamming  Zone 6 Slow Flash = RF Receiver Trouble  Zone 7 Lit steady = Data Bus Device Missing  Zone 7 Slow Flash = Data Bus Device Tamper  Zone 7 Fast Flash = Data Buss Device Trouble/Reset  Zone 8 Lit steady = System Fault  Zone 8 Slow Flash = Service Interval  Zone 8 Fast Flash = Ground Fault Condition Press Cmd to return to the off state.
    View full article
    ‎07-11-2018 06:37 PM
    Issue When attempting to connect to a DS7080iP-32 or DS7400Xi Ver4+ panel in WDSRP 2, Direct Connect does not appear as an option when Communicate is pressed. Solution WDSRP has not been set up to use Direct Connect function. Go to Utilities and Preferences, check Direct Serial Connect and press OK. Go back to Communicate screen and Direct Connect will appear.
    View full article
    ‎07-11-2018 06:35 PM
    Issue What is the 8 zone expansion module that is used on the DS7080IP32 control panel?   Solution   The EX8 would be the 8 zone expander module used to expand the DS7080IP32 panel. This expander wires on the keypad bus and can be addressed as 9-16 with no jumper (module address 101) or 17-24 with a jumper across pins 1 (module address 102), or zones 25-32 with a jumper across pins 2 (module address 103). You must use 9-16 first and power must be cycled after address changes for them to take effect.
    View full article
    ‎07-11-2018 06:30 PM
    Overview RF3401 wireless point always shows an open state, will need to be reprogrammed in the normal state.   Issue   RF3401 wireless transmitter using the External contacts stays open all the time (no change of state). Solution Transmitter must be deleted and relearned with the External point in the NORMAL state.
    View full article
    ‎07-11-2018 06:28 PM
    Issue An FA400 receiver that is disconnected will not force the keypad to display a missing message.   Solution   If two FA400 receivers are being used on the same D8125INV, the "Receiver Missing" message will not display if only one of the receivers is disconnected.
    View full article
    ‎07-11-2018 06:15 PM
    Issue How is the D6112 armed and disarmed? Solution Arming Your Security System Your security system can be armed in many different ways, depending on the arming command used. Arming commands are those commands used to arm the system. The most basic arming command is to arm the entire system. This is done by entering your personal passcode and pressing ENT or by entering COMMAND 1. To ARM your security system: Enter your personal passcode and press ENT or enter an Arming Command. Your system may be programmed to send a "closing" report to the Central  Station when arming. Disarming Your Security System Your security system is disarmed by entering your personal passcode and pressing ENT. When your system is armed, you must enter the premises through a designated entry door to prevent an immediate instant alarm condition. Opening the door starts an entry delay time and the Command Center emits a pulsing "beep" tone to remind you to disarm the system. Entering your personal passcode and pressing ENT before the delay time expires and the system will disarm. If you enter through a wrong door or fail to disarm the system before the entry delay expires, you will generate an immediate alarm. To DISARM your security system: Enter your personal passcode and press ENT. Your system may be programmed to send an "opening" report to the Central Station when disarming.
    View full article
    ‎07-11-2018 06:10 PM
    Part numbers D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4,
    View full article
    ‎07-11-2018 06:05 PM
    Issue What type of RF receivers are compatible with the D4412/D6412? Solution The ITI receiver part number RF3226 and the Bosch receiver part number RF3224.
    View full article
    ‎07-11-2018 05:59 PM
    Issue What do the command center warning tones mean? Solution Command Center Warning Signals The Command Center contains a built-in sounder used as an interior warning device. A bell or siren can also be mounted on the exterior of your premises to alert your neighbors of an emergency and to give the police an audible reference to help them locate the alarm. Several different warning signals are emitted from the Command Center to alert you when an event occurs (not all signals will be heard outside). Some of these tones are optional, and can be selected by your alarm technician. 1. Entrance Warning: The Command Center beeps during the entry delay period to remind you to disarm your security system. If the security system is not disarmed before the entry delay expires, an alarm signal may be sent to the Central Station and the alarm audible sounds. 2. Keystroke Entry: Pressing any key on the Command Center sounds a short beep tone, indicating that the entry is accepted. 3. Faulted Zone: The Command Center sounder is activated for two seconds after you enter an arming command to indicate that a zone is faulted, and the indicator of the faulted zone lights. 4. Watch Tone: When the Perimeter Watch Mode is activated, the Command Center emits a brief tone to alert you when any perimeter zone is faulted and the zone indicator lights to indicate which zone is faulted. The tone sounds only when the door or window is opened. It does not sound again for that zone until the door or window is closed and then reopened. 5. Service Tone: Some zones may be programmed to sound a service tone when they are faulted. The zone indicator light annunciates which zone is faulted. To silence the service tone, enter COMMAND 4 or enter your personal passcode plus ENT, at the Command Center. NOTE: Some zones, such as fire zones, may be programmed so that the sounder cannot be silenced until the zone fault is corrected My system can be silenced by entering COMMAND 4 or by using my personal passcode plus ENT. The system cannot be silenced unless the zone is returned to normal. 6. Telephone Trouble: If the security system cannot report to the Central Station due to telephone line trouble or other cause, the Command Center emits a steady beep tone. This tone may be silenced by entering COMMAND 4 or your personal passcode plus ENT.
    View full article
    ‎07-11-2018 05:55 PM
    Issue How to arm entire system with delays.   Solution   To arm the entire system with delays, follow the steps below: COMMAND 1 is used to arm the entire system, both perimeter and interior zones. Once you have entered COMMAND 1, the exit delay time starts. You now have a predetermined amount of time to exit the protected area before the system arms. During the exit period, you may move through motion detectors or any protected area on your way to the exit door without causing an alarm. To cancel COMMAND 1, enter your personal passcode and press ENT. NOTE: If you leave the building after the exit time expires, you may begin the entry delay, or initiate an alarm. If this happens, disarm your system by entering your personal passcode and press ENT . If your system reports to a Central Station, you may need to call them if an alarm occurs. Application COMMAND 1 is useful in applications where you want your cleaning service, a serviceperson or anyone to arm your system when they leave, but you do not want them to have the passcode to disarm the system. COMMAND 1 arms the system, but it will not disarm the system. Arming with COMMAND 1: 1. Ensure that all zones are secure. All of the Zone Status indicator lights on the Command Center should be off. 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the 1 key. The PERIMETER indicator and the INTERIOR indicator lights begin to flash on and off. This indicates that the system has begun exit delay time. 4. To disarm your security system or cancel COMMAND 1, enter your personal passcode and press ENT before the delay time expires.
    View full article
    ‎07-11-2018 05:50 PM
    Issue How can you arm the perimeter without delays?   Solution   Arm the Perimeter without Delays COMMAND 2 is used to arm only the perimeter of your building, leaving the interior of the building disarmed. This command allows no exit or entry delay time through the perimeter, including the designated delay door. Although this command does not send a "Closing Report" to the Central Station, it will still send alarms. Enter your personal passcode plus ENT to cancel COMMAND 2. Application This arming command is useful in residential systems at night when everyone is home and ready to retire for the evening. In commercial installations, this arming command is useful when you are working late and you want the perimeter of the building armed until you are ready to leave. Arming with COMMAND 2: 1. Ensure that all perimeter zones are secure (interior zones are not armed with this command and may remain faulted while arming with COMMAND 2). 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the 2 key. The PERIMETER  and INSTANT indicator lights comes on. This indicates that the perimeter zones are armed without entry/exit delay time. 4. To disarm your security system or cancel COMMAND 2, enter your personal passcode and press ENT before the delay time expires.
    View full article
    ‎07-11-2018 05:44 PM
    Issue Arming perimeter with delays   Solution   Arm the Perimeter with Delays COMMAND 3 is used to arm only the perimeter of your building, leaving the interior of the building disarmed. Once you have entered COMMAND 3, the exit delay time starts. You now have a predetermined amount of time to leave before the perimeter arms. Although this command does not send a "Closing Report" to the Central Station, it will still send alarms. Enter your personal passcode and press ENT to cancel COMMAND 3. Application This arming command is useful in residential systems when you are leaving, but members of your family, a babysitter or a pet are still inside the house. In commercial installations, use this command to rearm your system when you are on the premises, but not yet open for business. This command will not send a "Closing Report" to the Central Station. Arming with COMMAND 3: 1. Ensure that all perimeter zones are secure (interior zones are not armed with this command and may remain faulted while arming with COMMAND 3). 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the 3 key. The PERIMETER indicator light flashes. This indicates that the system has begun exit delay time. When the delay time expires, the light remains steady. 4. To disarm your security system or cancel COMMAND 3, enter your personal passcode and press ENT before the delay time expires.
    View full article
    ‎07-11-2018 05:38 PM
    Issue How do I reset the command center sounder and memory display? Solution Reset Command Center Sounders*Reset Alarm Memory Display COMMAND 4 performs two functions for your security system. Use this command to silence your Command Center sounder during service alert, and to reset the Command Center alarm memory. To use COMMAND 4: 1. Ensure that your security system is disarmed. 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the 4 key. The Command Center sounder is silenced and any flashing Zone Status indicator lights are turned off if the zone is normal.
    View full article
    ‎07-11-2018 05:34 PM
      How to View and clear Alarm Memory in the D6412 & D4412. D4412,D6412,D625,D623.  
    View full article
    ‎07-11-2018 05:33 PM
    How to transmit a manual test report from the D4112, D6112 or D8112.
    View full article
    ‎07-11-2018 05:27 PM
    Issue How do I do a local system test? Solution Local System Test It is easy for you to test your security system without sending reports to the Central Station. This local system test is performed only when the security system is disarmed to ensure that your security system is operating properly, and should be used to test your system regularly. COMMAND 44 is used to test your security system. This command tests your Command Center, the system’s sounders (both interior and exterior) and the system’s detection devices. No alarm reports are sent to the Central Station unless a 24-hour zone is faulted (e.g.: panic, fire duress). Contact your Central Station before you test your fire protection system because an alarm report may be transmitted. To test individual detection devices, simply activate sensors and open protected doors and windows one-at-a-time. As detection devices are faulted, the Command Center display panel indicates the faulted zone. This verifies that the detection device is working properly. To use COMMAND 44: 1. Ensure that the security system is disarmed. 2. Press the COMMAND bar. The Command Mode indicator light comes on. 3. Press the 4 key twice. Audible devices (both interior and exterior) sound. To silence the audible warning, press any numeric key of the Command Center keypad. 4. After silencing the audible devices, you may test detection devices. Open a door or a window, or activate a motion sensor. The Command Center display panel indicates the zone which you have faulted. This verifies that individual devices are working properly. 5. To end the Local System Test simply press any numeric key on the Command Center.
    View full article
    ‎07-11-2018 05:23 PM
    How to interpret the Alert Light flashing the DS7100 panel keypad after disarming. DS7140,DS7100.
    View full article
    ‎07-11-2018 05:22 PM
    How is the D6112 panel set up to have a smoke detector reset for 4 wire smokes? D6112
    View full article
    ‎07-11-2018 05:17 PM
    Issue What revision D2212 panel was compatible the the D169?   Solution   Revisions 2.53 and later panels are compatible with the D169 2-way voice.
    View full article
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist