Security: Intrusion

Overview Set up of a D6112 panel to have keyswitch arming. D611 is required. *Note -   D611 is no longermade. Issue Keyswitch arming the D6112 panel. Solution D6112 panel can use a D611 Key Switch Module. The D611 connects to the panels serial device data wiring. (connects in series like a keypad) Panel programming: 4.1 Device#     =    location in the series wiring of the serialdevice data                               1,2,3,4. 4.2 D#Model   =   1 6.1 Combo3    =   8 Notes D4112, D6112, and the D611 no longer made.

Part numbers D8112, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D1252, D1252A

How to transfer text from one DS7140 to another DS7140 on a DS7100.

Issue Can I mix Heat Detectors and 2 wire smokes with a sounder when using a D132A Smoke Detector Polarity Reversing Module? Solution No. When a Heat detector goes into alarm it puts a short on the input zone to indicate the alarm. The D132A uses Aux power from the panel when the polarity reversal takes place and since a heat detector does not reset when polarity is reversed, it would put a direct short on the Aux power of the panel. Consequently everything connected to the same Aux power terminals would not function.

How to disable reporting in the DS7090 or DS7090i. DS7090,DS7090I,DS7090TM,DS7090TMI

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+,

How to troubleshoot wrong point text displaying after a fire alarm is silenced on the GV2 panel type using firmware version 7.03 and a D1260 keypad.

Issue How do I clear alarm memory from the keypad?   Solution   On the D1260 keypad there are 4 buttons on the left and 4 buttons on the right side. Next to the bottom button on the right side should be a meesage that reads CLEAR DISPLAY. 1. Press the button beside the CLEAR DISPLAY prompt. 2. Enter your passcode. 3. Press the button beside the CLEAR prompt again. Now alarm memory should be off the display on the keypad.

Issue What are the steps to start and end the phone session programming?   Solution   1. House Phone: Press the # key three times, and enter the passcode when prompted. Default ( 5432 ) 2. Outside Phone: Dial the house phone number, and press * key three times when the call is answered, Enter a passcode when prompted 3. Installers Quick Connect: Connect a phone set to the control panel's test post. Press and hold the test button for approximately 15 seconds. Enter a passcode when prompted. Note: To end the phone session, Press the # key repeatedly until the system says "goodbye".

How to troubleshoot the DS860, DS950, DS970 LED Flashing 4 Times. DS860,DS970,DS950

Overview When wireless points are faulted, they display as 'Short' to the panel. When the wireless point tamper switch is faulted it will display as an 'Open' to the panel. Issue The panel when using a D8125INV and wireless points shows normal/faulted when point transitions from normal to off normal but the control always shows shorted. Solution Problem may be caused by another point expander connected to the control panel. Remove D8125INV from control panel and determine if points go missing. If points remain active (normal, faulted, etc) the control panel is interfacing with the points through another addressable point expander. Part numbers D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G, D8125INV, ISW-D8125CW, ISW-D8125CW-V2, FA400, EN4200

Issue What is the difference between the D133 an D134? Solution The D133 has a single relay rated at 2A @ 30 VDC – 0.6A @ 125 VAC. The D134 has two relays rated at 2A @ 30 VDC – 0.6A @ 125 VAC. Current draw for the Relay is 40 mA per relay when activated.

Issue What keypads will work on the D6112?   Solution   Compatible keypads are: D420A, 6 zone LED. This will work but only the first six zones will be displayed. D620, 8 zone LED. D626, 16 zone LED. D630, 8 zone LED with 3 onboard expansion points. D636A, 16 zone alpha display with 3 onboard expansion points

Overview The Bosch Security Systems D221 Answering Machine Disconnect Module allows you to remotely disconnect an answering machine that shares a phone line with a Bosch Security Systems control panel. When the answering machine disconnects the phone line is available to the control/communicator for remote programming (RPS) functions. A Touch-tone® telephone at the RAM site is required to perform the disconnect procedure. The D221 can be installed with an existing modular telephone jack or be a replacement for an RJ-11 jack.   Issue   What activates the module to disconnect the answering machine?   Solution   From a touch tone phone call the phone line, let the answering machine answer the line. The # key or the 8 key will activate the module. 1) module white jumper cut = # key 2) module black jumper cut = 8 key **Note: The RAM session is not affected when the D221 restores the phone line to the answering machine. Some answering machines record tones generated during the RAM session. If the D221 Module is used with an integrated telephone/ answering machine device, pressing the activation key ([#] or [8]) during normal use may activate the D221 and disconnect the device for 3 to 5 minutes.

Issue D7112 Panel battery will not hold a charge. Solution A slow flashing (1 sec on, 1 sec off) yellow LED with the green CPU LED off indicates a power supply overload condition.  The panel detects the battery as missing and the power supply cannot meet the power demand of the devices on the panel. The panel is shut down.

Issue Will an Answering Machine cause the D168A not to answer when accessed locally? Solution Some answering machines load down the phone line and cause it to go below 7 VDC. The D168A needs at least 7 VDC to properly process the DTMF tones.

How to determine why Central Station doesn't receive supervisory events sent with BFSK format. When sending signals using BFSK format, the central station does not receive Supervisory events.

Issue How can I tell a B series panel from a non B seies panel?   Solution   There are few ways. Look at the main eprom chip on the board, version 3.17 and under are a B series panel. It will also be labeled D9112B or D9112B1. Press CMD59 at a keypad, versions 3.17 and under are B or B1 series panels. Latch and unlatch the reset pin on the cpu. If it beeps for 8-10 seconds it is a B or B1 series panel.

How to determine why the BFSK/Relay or Output selected in Point Assignments, or points configured with Relay Response=2, do not reset as expected.