Security: Intrusion

How to correct the Panel reporting Extra Points on Zones 1-8. The keypad is displaying trouble due to extra point on an onboard zone(1-8). 5800C,5800G,5900C,5900G

How to configure Swinger Shunt to prevent points from automatically bypassing after  only 1 alarm. Why does the panel zone generate 1 Alarm and then goes into Swinger Bypass? D4412,D6412,DS7220,DS7240

How to set and View Date and Time using the D1255 Keypad.

How to locate the various connections and controls on the D636A keypad.

The keypad will display ‘Command Disabled’ when the Menu key is pressed for one of the following reasons. If the menu item # 1 in the function list is set with a function 0 and marked yes for any Command Center. If all of the Functions for the Command Center are selected as No (disabled). To prevent the keypad from displaying ‘Command Disabled’ after selecting Menu; Select a non-zero value for the Function # of Menu Item 1. Ensure that at least one of the Menu Items intended for use are set as Yes.

How to set the 4-button RF3334 RF Keyfob Trapazoid or Rising Sun key to activate an output.

How to correct the panel reporting RF Low Battery when there are no RF Devices Attached.

How to activate multiple auxiliary relays on Area Wide or Panel Wide Events.  Programming Area Wide or Panel Wide Relays will only allow a single relay entry.  Use an auxiliary relay such as the D130, D133 or D134 when multiple relays are needed to energize on a panel event.

How to address the B901 or D9210C on the SDI bus and how does the panel report an SDI Trouble.

How to troubleshoot the 2000 series panel when the keypad reads Call For Service. My D2212 reads "Call For Service" and does not show anything else.  How do I determine the issue? D2212, D2412, D2812

How to address SDI2 devices without causing address conflicts. Can different types of SDI2 devices use the same address setting? B810, RFRP-A, B820, B208, B308, B420, B426, B520, B920, B921C, B930, B942.

How to determine Popit Compatablity with the panel type. D9112B1, D9112, D9127T, D9127U, D9127, D8126T, D8126U, D8126, D8127T, D8127U, D8127

How to activate onboard relays from the panel keypad on 9000 – GV4 Series panels.

Part numbers D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4,

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3,D7412GV3, D9412GV3, D7212GV4, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G

Issue What is the process to set up auto arming on the DS7100?   Solution   To setup auto-arming perform the following steps: Enter a valid master code # 0,7 Enter address 05, then the auto arm time in 24 hour format then #. Example:  Auto arm at 10:30 PM.                Master PIN + #0 ,7,  05, 2300 #

Issue What are the steps on setting the panel time for the DS7100?   Solution   Enter in a valid master code # 0,7 Enter 01, then enter the time ( 24 hr. format ) then #