Security: Intrusion

Issue How many Logger Events can the D8112G2 store?   Solution   The D8112G2 Control Communicator can store up to 400 Events in the panel memory. The panel logs the time, date, event, master zone, and the primary or alternate phone number called for each event. The 400 events can be retrieved with the RAM II, RAM IV or RPS downloading software.

Issue How many Skeds can be programmed with the D8112G2 Control communicator?   Solution   The D8112G2 can be programmed with up to 64 skeds.

Keypad programming is available in GV3 panels with firmware revision 8.10 or higher.  NOTE: Keypad programming is not available during while an RPS programming session is active, or when any area is armed. Enter from normal operation: Press [9]+[9]+[Enter]. Select Keypad Programming. The keypad displays Enter Passcode. Enter the service passcode (default= 123). Enter from service mode (reset pin closed): D1255: Set the address to 16 with dipswitch: 1-5= OFF and 6= ON. The keypad displays Enter Passcode when the reset pin is closed. Enter the service passcode (default= 123). D1260: Set the address to 8 with dipswitch: 1-3= OFF and 4-6= ON. The keypad displays Enter Passcode when the reset pin is closed. Enter the service passcode (default= 123). The following options are available upon entering keypad programming: Phone Numbers – Phone 1 thru Phone 4 Phone Format - Phone 1 thru Phone 4 Enhanced Comm – Path 1 thru 4 Routing Route Groups 1 thru 4 RPS Parameters RPS Passcode RPS Phone Number RPS IP Address RPS IP Port Area Parameter – 1 thru 32 Account On – Yes / No Account Number Command Center 1 thru 16 Enhanced Command Center – Yes / No Command Center Scope – User Pass Code User 0 (Install Passcode) User 1 (User Passcode) Point Parameters D9412GV3: 1-247 D7412GV3: 1-75 D7212GV3 1 -40 Point Index Disable Keypad Programming

Issue How can a command function such as CMD 47 be used without entering a passcode at the keypad?   Solution   To use commands without a passcode required, disable the command function under the Authority Level Configuration for all authority levels. This will allow the function to be used without a passcode.

Issue What is the difference between the D9124 and the D9412G?   Solution   The D9124 is a D9412G with a 24 Vdc PSU and all the needed Fire Accessories for a basic system, all in one large red enclosure. See parts List below. The D9124 is made up of the following : D9412GLTB - Control Panel D9101 - Red Enclosure D9100 - Carriers Module with the Foolowing parts * * 2 - D192C - Bell Supervision Modules * 1 - D8125 - Popex Module * 1 - D928 - Dual Phoneline Switcher * 1 - D9142LC - 24Vdc Power Supply D1256 - Fire Keypad D1601 - Hardwire Transformer

Overview: The FA422 Programming Cable has a 2 pin female connector at the transmitter end. Inovonics transmitters have 3 pins on them. The center pin on the transmitter is for Data and the 2 outer pins are ground. The 2 pin connector connects to the center pin and either of the outer pins on the transmitters when programming. Issue The programming cable for the FA422 receiver only has 2 pins at the transmitter end. How does the 2 pin connector connect to the 3 pin transmitter? Solution Connect the 2 pin connector to the center pin and either outer pin. Either way will work.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, D1255, D1260, D1265

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4, DS7447

Overview: Keypad displays  a flashing "service perimeter" because a zone is or was faulted. Issue Keypad displays a flashing "Service Perimeter" with no zones displayed.   Solution   A Perimeter zone is or was faulted. If a zone is displayed, the zone must be made normal first. If no zone is displayed,  enter CODE + ENTER + CLEAR + CLEAR . This will clear the keypad memory.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers D8112, D8112A, D8112E, D8112E1, D8112G, D8112G1, D8112G2, D8105E, D8105E1, D8105G, D8105G1, D8105G2, D8105A

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7212G, D7412G, D9124G, D9412G, D7212GV2, D7412GV2, D9124GV2, D9412GV2, D7212GV3, D7412GV3, D9412GV3, D7212GV4, D7412GV4, D9412GV4, B8512G, B9512G

  How to determine whether the Inovonics repeater can be installed outside. ISW‑EN5040‑T, EN5040‑T, Repeater, Echostream.  

How to determine the max available current for point 1 in the D4412 or D6412.

How to learn the RF3502 into the panel; as a point or a keyfob assigned to a user? D4412, D6412, RF3224, RF3502

How to troubleshoot when the D6412 or D4412 panel will not release the phone line.

How to access the IP Communicator Web Browser.

How to add ITI transmitters, are they added in normal or faulted condition? D4412, D6412, RF3226, ITI WIRELESS DEVICES.