About Central_Support

Question   Where is the “Display stamping” submenu of FLEXIDOME multi 7000i (CPP14 - Bosch cameras) in WEB UI?   Answer   ‘Display stamping’ submenu has been moved from the General menu to the Camera menu. Open one browser Type the IP address of your camera Go to Configuration > expand the Camera menu. The "Display stamping" menu will be displayed there. Options are much more flexible than in the previous cameras, they are now like CPP13 cameras (INTEOX). ... View more

Possible causes and solution(s)   The camera may be out of focus during a rapid zoom change if: There is a large amount of reflection with full sunlight. Or, there are headlights or bright lights present at night. This problem occurs most often when used in traffic applications.   Causes:   The camera tries to focus on the bright lights and fails to find the correct focus position (example snapshot of headlights below).   Solution: The camera block FW version 1.05 and higher has a new feature called “Spotlight Avoidance” for cameras made in November 2018 and later (table below). This improves the cameras ability to ignore the “bright lights” while focusing. It will base the focus on the rest of the FOV. This is useful in challenging conditions such as traffic flow, airports, and areas with a large amount of bright lights at night. Refer to the table below for the models that support this feature. Please see also the following article: MIC 7000i/9000i - Camera Block Firmware Upgrade for Firmware 7.60.0118 and higher This is OFF by default, since in most applications it is better to use the entire FOV to obtain the focus. There isn’t a Config Manager or Web GUI setting available to activate this. The command to activate this is listed below. Additional Options: If there are still problems with focus in these conditions after Spotlight Avoidance is activated, then the following settings can be adjusted. Reduce the Iris Level from 8 down to 6 Daytime video will be improved by setting the Day Near Focus Limit to 3. The nighttime video will be improved by setting the Night Near Focus Limit to equal the mounting height of the camera. Set Spotlight avoidance ON http://<IPAddress>/rcp.xml?command=0x09a5&type=P_OCTET&direction=WRITE&num=1&payload=0x81000405300381010424200001ff GET Spotlight Avoidance Status http://<IPAddress>/rcp.xml?command=0x09a5&type=P_OCTET&direction=WRITE&num=1&payload=0x8100040530038109042420ff Look at the last 2 digits prior to FF. It should be 01:   Additional Applications -Recommended Settings: Highway Settings: To maintain color mode as long as possible   CONFIGURATION/CAMERA/INSTALLER MENU: Change Sensor mode: 30 FPS CONFIGURATION/CAMERA/PICTURE SETTINGS: o Change Maximum Automatic Exposure to: 1/15 o Change Night Mode Threshold to: 20 o Leave the default setting of NIGHT MODE PRIORITY as COLOR. NOTE: The headlight “blooming effect” is less in Color mode since the stray IR light from the headlights is blocked. This is why it is an advantage to operate in color mode longer.   Miscellaneous If more Contrast is preferable: CONFIGURATION/CAMERA/ENHANCE: o Change Intelligent Defog Intensity to ON -Select Low, Medium, or High.  Note The spotlight avoidance is not available/ supported by the new camera blocks (MIC 7100i models). This feature is automatic in MIC 7100i camera models blocks. ... View more

Possible causes and solution(s)   MIC IP 7000i/ 9000i Bosch camera - Camera Block Firmware Upgrade for Firmware 7.60.0118 and higher   Cause:   MIC 7000i with FW 7.72 shows blurred images. After restart, the quality of the image is good for a short time, but the issue reappear.   Only Applicable to these models: MIC 7000i (MIC-7502-Z30x) MIC 9000i (MIC-9502-Z30x)   System Requirements Web Browser: Microsoft Internet Explorer 11 or Mozilla Firefox; DirectX 11; Bosch MPEG-ActiveX 6.33 and Configuration Manager 6.20 or higher Prerequisite - Serial Numbers impacted (Camera block FW less than v1.06) A new camera block was released in November 2018, but the CTN # didn’t change. The two digit lot code in the serial number was incremented. This upgrade is only applicable to this lot code or higher. NOTE: If the CTN # isn’t provided, the 4th digit of the S/N is the Type Code that can be used to identify the applicable CTN. Please note that the digits 13 and 14 Lot Code ranges are different for each CTN.   Overview The upgrade takes place in two steps. • The first step is to update the entire camera using either Configuration Manager (CM) or the Web Browser. This uses the standard upgrade process. • The second step requires the Web Browser to start the internal camera block FW upgrade. Once the camera block FW upgrade has started, the remainder of the upgrade takes place inside the camera.   Solution:   Step 1: FW upgrade to FW 7.60.0116 or higher – Using either CM or Web Browser – These MIC cameras should never have any FW version less than 6.60. • In order to upload version 6.51 or higher to a device running a firmware version below 6.50, you need to upgrade first to version 6.50, since older firmware versions do not support firmware file • A video loss after the upgrade is possible. If this occurs, reset the camera again. • It is recommended to Default the camera after the 7.60 FW upgrade is completed.   Step 2: Camera block upgrade to FW 1.06 - This step must be initiated using the Web Browser. IMPORTANT: – Neither the Live page nor the Live preview window will refresh during the camera block FW upgrade, since no video is available for during this time. Video recording is also not possible during this process. – Make sure the camera has power continuously. (Do not remove power to the camera during the upgrade) 1. Browse to the CONFIGURATION>SERVICE>LOGGING>EVENT LOGGING; and then select NOTICE from the CURRENT LOG LEVEL drop down box. This is required to be able to see the progress of the FW upload. 2. In the URL field in the camera’s Configuration page, type the text that follows: http://<IPAddress>/Settings.html#page_cam_upload 3. The “Camera module upload” window appears and the current version of the camera block FW version is checked. – If the FW upgrade isn’t needed or isn’t applicable, then the message “Camera upload possible: 0” is displayed and the Start Upload button is disabled. – If an upgrade is required, the message “Camera upload possible: 1” will be displayed and Start Upload button will be available. 4. Click Start upload. The camera begins the firmware upload cycle which will take approximately 15 minutes.  Do not navigate to another GUI page and Do not remove power to the camera!   5. The progress of the FW upload is tracked and updated in the web browser. This screen shot is the example of the beginning of the process. Do not navigate to another GUI page and Do not remove power to the camera!   6. After the upload completes successfully, the message will go back to “Camera upload possible: 0”and the Start Upload button will be disabled again. The camera will reboot automatically. 7. After the reboot cycle completes, change the EVENT LOGGING LEVEL back to WARNING. 8. If the original FW was less than 7.10 then a Factory Default is recommended. If a factory default is going to create problems with the VMS, then use the camera as is. If any video quality or focus issues occur, then do a factory default. ... View more

According to its Data Sheet, the Flexidome IP 3000i IR camera has 2 options to activate the alarm input.   Step-by-step guide   The pin assignment for the alarm I/O is the following: Pin number 1 → Signal Alarm output Pin number 3 → Signal Alarm input   Wiring diagram for alarm input The following diagram demonstrates how the device triggers alarm input through the external mechanical switch or through the external open collector circuit.   A full Alarm wiring guide for 3000i cameras it’s available for download on the web catalog here. Please refer to the diagram below if you would like to get alarm input from some physical sensors.   Connect Alarm Input / Output Port:   Mode A:  Level application: Alarm output low level, alarm output is Open Collector (OC); It needs to increase pull-up resistance externally to work normally. After external pull-up resistance is loaded, the default output signal is high level (external pull-up voltage), and it switches to low level when there is alarm output. Mode B:  Switch application: Alarm output is used to drive external circuit.   ... View more

The camera supports the SNMP V1 (Simple Network Management Protocol) for managing and monitoring network components, and can send SNMP messages (traps) to IP addresses. It supports SNMP MIB II in the unified code. You may need the SNMP MIB file when you are trying to monitor the camera through a Bosch or 3rd party software. This article aims to describe how to find and enable the SNMP on a Bosch camera. Article requirements: IP camera PC Same LAN connection between the camera and PC   Step-by-step guide   A) Where can you get the SNMP MIB for your IP devices: cameras, encoders, VRM? For cameras and encoders, the mib file is included in the file when you download the .zip firmware from the camera's product page (go to Downloads > select Software > download the .zip file you need).   Unzip the Firmware file and you will find the .mib file there:   For IP camera operating on firmware 7.50.xxx and below, you can find it on the web page of the camera, using the following url:  http://camera ip/snmp_cmds.htm. For example: a camera with 192.168.10.1 IP address, the command looks like the following:  http://192.168.10.1/snmp_cmds.htm   For VRM it is included in the installation files you can download from the web page. Each version of VRM has a different MIB file.   B) Activate the SNMP on the camera:  Go to the web interface using Internet Explorer or any other browser (type its IP address) Login in to the camera Go to Configuration >Network >Network Management Select the desired SNMP version (v1 or v3) , click on Set > Set and Reboot After the camera reboots, enter an SNMP Host address (where the traps will be sent). Select from the dropdown menu of the SNMP Traps > the desired traps that you wish to be sent   How to send SNMP v1 requests to Bosch cameras? How to send SNMP v3 requests to Bosch cameras? ... View more