Fire

Listed in the table below you will find the old DS MUX Device part number with the new MUX Device replacement. Replacement Part Numbers Old DS MUX Devices Description FPE-7039, D7039 DS9331, DS9431R MUX Card D7050-B6 MXB2W MUX Base D7044 MX361 Single Point D7044M MX361M Mini Single Point FMM-7045 MX310 Pull Station FMM-7045D MX310D Dual Action Pull Station D7052 MX363 Dual Point Module D7053 MX46 I/O Input/Output Modules D7050 MX250 MUX Smoke Head D7050TH MX250TH MUX Smoke Head with 135 Heat Sensor  .

From RPS in the following panels DS9400, DS9400I, DS9400M, D7024, and FPD-7024 you have the option to set Anti-takeover Setting to one of the following. a.)Allow all local programming: All programming items may be accessed from the local keypad. b.) Lock phone/account numbers only: All programming except phone numbers and account numbers may be accessed from the local keypad. c.) Lock all local programming (except Date/Time and all user PINs): Allows only the Date and Time to be set from a local keypad.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, D8512G, B9512G, D1255, D1255W, D1255R, D1255RB, B915, B920, B921C, B930, B942, D1260, D1265, B925F, B926F,

Part numbers D10024A, D10024, D9024, D8024

Part numbers FPA-1000, FPA-1000-V2, FPE-1000-NE, FPE-1000-NW, FPR-1000-NF  

Overview When devices are connected to the Option Bus on the FPD-7024, the bus must be scanned allowing the panel to see the device. After removing devices, such as the DX4020, DX4010V2 or DX4010i, the option bus must be scanned again to complete the removal, or the panel continues to supervise the device resulting in a keypad display: Trouble DX4020 and history event: SYSTRB017. Issue After completing programming the panel reports trouble DX4020; history shows SYSTRB017 Solution After removing the DX4020, DX4010V2 or DX4010i, the option bus must be scanned again to complete the removal or the panel continues to supervise the device.  From the Panel Keypad (not a remote keypad) perform the following steps to update the option bus: Select 0 for PROGRAMMING and enter the installer code Select 3 for PROGRAM SYSTEM Select 4 for OPTION BUS Select 1 for UPDATE BUS

Contrast Adjust on FPA-1000, FPA-1000-UL, and FPA-1000-V2 panels

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D1256

The FLM-325-2i4 is a Single address Dual Input Analog Addressable Module with two inputs used to monitor Normally Open (NO) or Normally Closed (NC) circuits.  If the module is addressed as 010 the First input will display as 010.1 on the panel keypad display, the Second input will display as 010.2 on the panel keypad display. 

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, FPE-7039, D7039, DS9431

Part Numbers, FAD-325 (DUCT Housing without Relay), FAD-325-V2F (DUCT Housing without Relay), FAD-325-R (DUCT Housing with Relay), FAD-325-V2F-R (DUCT Housing with Relay) FML-325-2R4, FML-325-2R4-2A, FML-325-2R4-2AI, FML-325-2R4-8A, FML-325-2R4-8AI, D323DH (DUCT Smoke Head), FAD-325-DH (DUCT Smoke Head), FAD-325-V2F-DH, FPA-1000, FPA-1000-UL, and  FPA-1000-V2.

Configuring the FPP-RNAC-8A-4C on an Option Bus Fire panels FPD-7024 & FPA-1000.

Part numbers FPD-7024, D7024, DSS9400, DS9400I, DS9400M

Mux Card replacement (DS9431, DS9431R, D7039, or FPE-7039) on any of the following panels DS9400, DS9400I, DS9400M, D7024, and FPD-7024.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G,

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G

Issue Can the points, outputs and dialer be enabled and disabled from RPS? Solution No, This can only be done from the panel or a keypad attached to the panel. If any of the hard wire points are disabled then follow the steps below to enable points 1-8. Mux points 9 - 255 can be enabled using the "all" command if points 1 - 8 are enabled individually first. To Enable Points Press the Disable Button on the keypad. Press 2 Enable Press 1 Inputs Press 2 Individual Enter the point # (001 - 255) follow by # Repeat steps 3 – 5 until Points 1 -8 are enabled Press 1 Inputs Press 1 All Press the * Clear Button 4 times Follow the steps as above to enable Dialer - NAC's and Relays.

How to access the Menu features on the B926F which does not have a Menu button.

Part numbers D8125MUX, D7050, D7050TH, D5060, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G,

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G