Fire

In the event of flames and smoke, the camera's built-in intelligent algorithms analyze the scene in real time by concatenating and transforming the input data. Deep learning AI directly analyses the data and if a fire is confirmed, it triggers an alarm and sends a signal either to the fire panel or the Video Management System.

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M,

How to correct the FPD-7024 or D7024 error: Programmed Points Exceeds Max. How to correct the FPD-7024 or D7024 error: PRGRMMD POINTS EXCEED MAX.

A sticker on the front of the B450 indicates proper switch positions for selecting various SDI or Option Bus addresses (see figure 1). Figure 1 Sticker with address configurations   There are 2 types of FPD-7024 panels. It must first be determined which is in use before selecting the B450 address: Newer types with firmware version 1.06 and higher. These types are identified by icons on the keypad instead of words (see figure 2). Older types with firmware version 1.03 and lower. These types are identified by words on the keypad. Figure 2 Version 1.06 with Icons vs 1.03 with words   Version 1.06 & newer types: When used as sole communicator or backup to phone line, set the address wheel at 9 for Option Bus address 250. When used as backup to a primary network communicator, set the address wheel at 6 for Option Bus address 134. RPS connections require Option Bus address 250. Be sure the address wheel is set at 9 on the network communicator intended for RPS connections (Ethernet is preferred when allowed). Version 1.03 and older types: Use Option Bus address 250. Only one network communicator is available on these panel types.

Part numbers DS240, DS241, D296, D297

With FSM 5.6  the database.xml structure was slightly changed and FSM 5.6 is supporting only the new database.xml structure. This is leading after upgrade to a loss of the configured symbols (only the symbols, not the content of the devices configured on the floor plans). Therefore after upgrading from older FSM version (e.g. 5.2) to 5.6, the already configured symbols of sensors on maps are not shown correctly, they are shown are dots/circles.   Please note: If before executing the file provided below the application was opened and the sensor properties were edited by approving > at that step the symbols changed to the default symbol and the previously configured symbol cannot be recovered.

Part numbers D7052, D7024, FPD-7024, DS9400, DS9400I, DS9400M, MX363

This article describes how to capture the panel/ controller communication log when requested by Technical support.

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, D7034, FPE-7034, DS9434

If FSM needs to be connected to a new panel (network), then proceed as it is described in this article:

This is how to troubleshoot where turning the key to the Test position does not put the smoke detector inside the duct enclosure into alarm, which will likely be due to the coil is missing.

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M,FPP-RNAC-8A-4C, DS9484, DS9488, D7035

Follow the steps from this article to access the Point Description programming.

This article provides instructions for exporting and saving the program from an FPA-1000 to be imported into a replacement FPA-1000 panel. This information may be needed when replacing an FPA-1000 fire panel with another with intentions to use the same panel program.

The license key is not stored in plain text therefore is not possible to view, but the associated order number can be identified.

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, DS9447, DS9436, D7033, D7036, FMR-7033, FMR-7036

This article indicates where you can find the log files for FSM client and for FSM server

Part numbers FPD-7024, D7024, DS9400, DS9400I, DS9400M, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G

This is a generic solution for any photoelectric device application where the device seems to keep going in and out of trouble due to alignment issues. Part numbers DS240, DS241, D296, D297

This article explain how it is possible to automatically zoom in the map in case of alarm.