Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Access Control

    Sort by:
    ‎07-10-2018 09:06 PM
    Article describes "invalid badge, facility code and format" messages
    View full article
    ‎05-16-2018 04:36 PM
    This article explains whether a  D6686 be used to integrate a D6600 or D6100 with Readykey Pro
    View full article
    ‎06-14-2018 02:33 PM
    Article offers a possible solution for "free memory low" rdkypro message
    View full article
    ‎06-13-2018 02:38 PM
    Article describes how to setup schedular for archiving and purging the database
    View full article
    ‎05-11-2018 05:20 PM
    This article provides the solution when the computer cannot access the AEC2.1 if the Lantronix device is on the same subnet as the AEC2.1.
    View full article
    ‎06-22-2020 10:27 PM
    Set up Interlock APE 
    View full article
    ‎01-18-2021 06:18 AM
    AMS 3.0 How to configure Dual factor Authentication (Card + PIN)
    View full article
    ‎06-13-2018 02:33 PM
    Article describes how to set 1320 reader voltages
    View full article
    ‎06-05-2018 03:59 PM
    How do you upgrade an access panel in ReadykeyPRO?  Upgrading a panel becomes necessary if the current access panel does not have enough memory for the system or needs to be replaced for maintenance.
    View full article
    ‎03-31-2020 10:10 PM
    1. Open “Card personalization Configuration”. You can find this software by accessing the “Access Professional Edition” folder in the start menu. See figure 1. If unable to find in the start menu, this is located in the folder “C:\BOSCH\Access Professional Edition\CP\bin\SfmCfgApp.exe”, (unless non-default paths and folder names are chosen during installation). See figure 2.   Figure 1 Figure 2 *Note: Make sure to run the software with administrator rights.   2. In Card personalization Configuration go to the Print tab.   Figure 3   3. Create a print channel. Type the print channel desired name and click the button to the left.   Figure 4 Once the print channel is created, the installed printers at this PC will populate below.     Figure 6   4. The printer’s information will auto fill under the current channel, modify parameters as needed.   Figure 7   5. Once finished, click apply and close.   Figure 8   6. Restart the computer.
    View full article
    ‎05-11-2018 01:52 PM
    These are steps to assist with troubleshooting the AEC 2.1 time drifting.
    View full article
    ‎05-22-2018 11:43 AM
      Readykey Pro use custom barcode
    View full article
    ‎07-02-2020 04:40 PM
    How to set up Dual Factor Authentication (Card + Pin) APE
    View full article
    ‎05-14-2018 05:25 PM
    Why doesn't the Assign Card dialog box open when entering cardholders in Access Professional Personnel Management?
    View full article
    ‎05-22-2018 11:36 AM
      Related ProductsReadykey Pro Question How can I ensure that clients do not change certain features that require exclusive use of the SQL database for Readykey Pro? Answer Certain activities require that there are not any applications logged into the SQL database. These activities include running a database backup, archive, database setup, or forms designer. In some cases, a server has many clients logged into the database remotely. This makes it difficult to close all client connections. There is an easy way to work around this by running a few SQL commands. Login to SQL Management Studio Express. Expand the Databases folder and find AccessControl (for example, the Readykey Pro database). Right click on AccessControl and select New Query. In the query window, type: sp_who2 [Click EXECUTE]. Look for all SPID that have the login type of lenel. For each SPID number of login type lenel, type: kill (SPID) [Click EXECUTE]. IMPORTANT: Do not kill SPID for SQL Server, as this will kill the Management Studio connection. Run the required application (for example, Database Backup). This method does not prevent future connections to SQL Server. If an exclusive connection is required, the port SQL Server uses can be blocked by a firewall (for example, TCP port 1433). You should block ports with caution because it may also block local connections. A better solution would be to temporarily disable remote connections to SQL Server using SQL Server Configuration Manager.
    View full article
    ‎05-22-2018 11:46 AM
      What effect does losing communication with the server have on an access controller
    View full article
    ‎03-31-2021 10:04 PM
    Scenario User needs to activate a relay when the door is held open, but they do not have an I/O board.   Solution Create an One Shot Advance I/O event to trigger the relay output desired. See below step by step how to do it.   Create a “Criteria” specifying the event we want to use to activate the relay output   Go to “Configuration” and then “Criteria”   Figure 1.   Click the “green plus” to create a new Criteria   Figure 2.   Under description assign a name In this example, the user only wants one door to trigger one relay, Click “Selected Devices Only”, select the desired door and add it to the “Selected Devices” column   Figure 3.   Click the “Events” tab   The user only wants the relay triggered by one specific event: “Door held open”. Click “Selected Events Only”. Add the desired event to the “List of Selected Events” column   Figure 4.   If this action is desired to happen only in one specific schedule, click the “Time” tab and choose the desired schedule. Click Save   Figure 5.   Create an Advanced IO to assign the Criteria for activating the relay output   Go to “Configuration”, and click “Advanced IO”   Figure 6.     Click the “green plus” to create a new one   Figure 7.   Under description assign a name for the new Advanced I/O The function needed is “One Shot” Select the output duration desired The “Input Control” is the criteria previously created. Click the edit button, select “Criteria” and the name assigned to the Criteria The “Output Link” is the relay output we want to activate. Click the edit button and select the relay output desired. Click the save button   Figure 8.
    View full article
    ‎06-01-2018 05:50 PM
    Describes reasons for facility code error in AEC
    View full article
    ‎06-12-2018 03:42 PM
    Article lists AEC and Allplex network ports.
    View full article
    ‎06-13-2018 02:43 PM
    Article gives possible reason for green and white rdkypro icon in Alarm Moinitoring
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist