Security: Intrusion

How to determine the max wire length and number of keypads available on the DS7090. DS7090,DS7090I,DS7090TM,DS7090TMI

Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7420i

Issue Can not get some of the functions to work on the command center. Overveiw: Some functions require you to enter single partition mode when using a master keypad. Soultion The following command require that you are in single partition mode when entering from a master keypad. ( valid code ## ) History read-back Chime mode Checking zone status Checking zone troubles status Bypassing zones      Part numbers DS7400X, DS7400, DS7400Xi, DS7400XIVER2, DS7400XIVER3+, DS7400XIVER4+, DS7447, DS745, DS7447E,  

How to determine the maximum wire distance for the DS7091. DS7090,DS7090TM,DS7091

Issue What do the error displays mean on the DS7080i ? Solution Error Displays Control panel problems are indicated by a flashing green Power Light. The DS7447 display will also read “Control Trouble, Enter # 8 7.” The DS7445 will only flash the green Power Light. The Error messages may only be read when the control is disarmed. Contact your installing company if the problems persist. 1.) DS7447 - “AC Power Failure”: DS7445 - LED 1 turns on steady: There is a power failure and the panel is operating on backup battery. 2.) DS7447 - “Battery Trouble”: DS7445 - LED 2 turns on steady: If the system has just been through a power failure, wait at least two hours for the battery to recharge, then enter a PIN + [System Reset] to perform a battery test. 3.) DS7447 - “Communicator Err”: DS7445 - LED 3 turns on steady: The communicator failed to communicate with the central station. 4.) DS7447 - “System Fault”: DS7445 - LED 4 turns on steady: Internal error in the control circuitry or optional circuitry. These faults are displayed as follows: RAM Fault ROM Fault EEPROM Fault TRBL Zone Fault. 5.) DS7447 - “Keypad Fault”: DS7445 - LED 5 turns on steady: One of the keypads is not responding to the control panel. 6). DS7447 - “Aux Power Fault”: DS7445 - LED 8 turns on steady: The auxiliary power has been shorted. 7.) DS7447 - “Zone Trouble”: DS7445 - LED 6 turns on steady: One of the zones is not responding to the control panel. This may also be displayed during power-up (if so, ignore). * = If in “Residential Mode”, a PIN is not required for these commands. ** = Battery Trouble and Communicator Err displays must be cleared by the [System Reset] command sequence even after the problem has been remedied. These displays will not self clear. All the other error displays will self clear from the keypads once the problem has been remedied.

  How to perform Zone Test from a Master Keypad on the DS7400 Series. DS7400,DS7400X,DS7400Xi,DS7400Xi (Ver 3+),DS7400Xi (Ver 4+)  

Issue Trouble connecting to the D4412 with RPS / RAM IV using the DX4010i. What dip switches need to be set to make the DX4010i connect to the panel? What type of cable is needed between the DX4010i and the Laptop or PC? Solution RAMIV / RPS needs to be revision 3.6 or higher. Set the address 0 (Installer's mode) Dip Switches 6 and 8 in the off postion on the DX4010i. Use a NULL cable to connect the DX4010i to the Laptop or PC. For remote programming connection, use the RJ-16 to molex connector to the Aux / Data header. Lock the Installer or Reset Pin on the panel. In the RSP/ RAMIV Connection screen change the connection type from MODEM to ENHANCED DIRECT, then click connect. *If connected to a D4412 panel and the address is set wrong on the DX4010i then a message of "INVALID RAM PASSCODE" may be generated.

How to enable/disabling encoding tones on the D1254 Keypad used wth the D7112.

How to interpret the Alert Light flashing the DS7100 panel keypad after disarming. DS7140,DS7100.

Issue What is the 8 zone expansion module that is used on the DS7080IP32 control panel?   Solution   The EX8 would be the 8 zone expander module used to expand the DS7080IP32 panel. This expander wires on the keypad bus and can be addressed as 9-16 with no jumper (module address 101) or 17-24 with a jumper across pins 1 (module address 102), or zones 25-32 with a jumper across pins 2 (module address 103). You must use 9-16 first and power must be cycled after address changes for them to take effect.

How to bypass the tamper input on the DX2010.

How to determine how many keypads are supported on the DS7060 and allowed wire distance. DS7060,DS7447,DS7445,DS7443

D7112 Overview: Firmware Revision 3.57 is NOT compatible with the D7112 panels with a date code of X9416 or higher.   Issue   Panel is non responsive to any programming.   Solution   Firmware Revision 3.57 is NOT compatible with the D7112 panels with a date code of X9416 or higher.

How to correct the D8128A is inoperative when wired according to terminal labeling. D7212B,D7212B1,D9112B,D9112B1,D8129,D7112

How to make the DS7060 panel send a 3 digit account number.