Security: Intrusion

Issue How do I clear alarm memory from the keypad?   Solution   On the D1260 keypad there are 4 buttons on the left and 4 buttons on the right side. Next to the bottom button on the right side should be a meesage that reads CLEAR DISPLAY. 1. Press the button beside the CLEAR DISPLAY prompt. 2. Enter your passcode. 3. Press the button beside the CLEAR prompt again. Now alarm memory should be off the display on the keypad.

Overview When wireless points are faulted, they display as 'Short' to the panel. When the wireless point tamper switch is faulted it will display as an 'Open' to the panel. Issue The panel when using a D8125INV and wireless points shows normal/faulted when point transitions from normal to off normal but the control always shows shorted. Solution Problem may be caused by another point expander connected to the control panel. Remove D8125INV from control panel and determine if points go missing. If points remain active (normal, faulted, etc) the control panel is interfacing with the points through another addressable point expander. Part numbers D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G, D8125INV, ISW-D8125CW, ISW-D8125CW-V2, FA400, EN4200

How to determine why the BFSK/Relay or Output selected in Point Assignments, or points configured with Relay Response=2, do not reset as expected.  

Part numbers D7412, D9412, D7412G, D9412G, D7412GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B6512, B8512G, B9512G, D9210, D9210B, D9210C, B901

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4, B8512G, B9512G, D1255, D1255RB, D1255R, D1255W

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D9124G, D9412G, D7412GV2, D9124GV2, D9412GV2, D7412GV3, D9412GV3, D7412GV4, D9412GV4,

How to Correct the panel sending point restorals but not sending alarms.

How to correct the D1255 Command Center going blank while selecting menus. While entering key stroke commands and using the Menu option on the D1255, the display blanks out and the speaker crackles then the display comes up after 5 seconds.

How to configure the DX4020 for Different Ports.

How to correct custom functions that execute when A, B or C keys are pressed on the D720. D1256 Command Center functions are Executing when A, B or C Keys on a D720 are pressed.

How to supervise the DX4020 on the SDI bus.

How to correct points 001-008 reporting in COMEX format as 100-800.

I am able to arm the area with a 24 hour point violated in the same area. How can I prevent the area from being armed with a 24 Hour point violated? 24hour points do affect the 'ready to arm' status of the area, therefore will not prevent the ability to arm after clearing the alarm while the 24hour point remains faulted.   Program the 24 Hour Point as a Type 1, Response 9.  When using point response 9, the point will operate as a 24hour point.  However  because this will become a controlled point it will prevent arming until either satisfied or bypassed (if the point is configured as bypassible).

How to correct when the command center goes blank as soon as the last area arms. Why does the command center goes blank as soon as the last area arms?

How to configure the Swinger Count and use Swinger Shunt.