Security: Intrusion

Best practices to download and Install Remote Programming Software (RPS).

How to interpret the Comm Trouble SDIxx or Comm Fail SDIxx display.

How to troubleshoot Comm Fail when intrusion alarm panels communicate over phone lines. What would cause a control panel to go into Comm Trouble or Comm Fail?

How to troubleshoot problems with popits and Zonex. D7212B, D7212B1, D9112, D9112B, D9112B1, D9127,D8112, D8128A, D8112B, D8128C, D8128D, D8125

How to troubleshoot Low or Missing Battery Troubles.

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G,

How to add or Modify user and access credentials. How can I add or modify a user or access card/token/pin using the D1255 keypad? D1255,D1255R,D1255RB,D9210B

What are Point Profiles and how are they used to program points on B8512G/B9512G or B-series panels? How to program the B3512. How to program the B4512. How to program the B5512. How to program the B6512. How to program the B8512G. How to program the B9512G.

Article describes the "alarm panel substitution" message

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4, B8512G, B9512G

How to understand Point Profiles or Point Indexes when programming G Series or B Series control panels.

How to set and View Date and Time using the D1255 Keypad.

This Setup & Troubleshooting guide for the B426/B420 Conettix Ethernet Communication Module contains valuable instructions for configuring the IP Communicator.  Included are detailed instructions for using the web interface on SDI bus configurations as well as panel programming for SDI2 bus configurations.  Configurations for remote programming and central station reporting are also included.

How to configure Door Control on both sides of a door with B8512G, B9512G or B6512 panels. How to configure Door Control for Card-In and Card-Out with B8512G, B9512G or B6512 panels. How to configure Access Control for Card-In / Card-Out with B8512G, B9512G or B6512 panels.

How to configure the RK40 iCLASS pin reader for 26-bit output. ARD-RK40-09, ARD-RK40-14

Overview: Missing points are points that are turned on in programming via the Point Index assigned to anything other than 0  and cannot be found by the panel on the Zonex Loop. This problem may have a number of causes such as; the point is actually not in the field, is wired incorrectly, has a faulty addressing device such as its POPIT or Octopopit, or there may be noise in the data loop. When Points go missing, the panel generates responses based on the point type. Fire points generate Missing Trouble responses, non-fire 24 hour points will generate Missing Alarm responses. Points that are neither Fire nor 24 hour points will generate Missing Alarms when armed and Trouble when disarmed. Issue Panel history shows Missing Alarm. What does it mean? Solution This problem may have a number of causes such as; the point is actually not in the field, is wired incorrectly, has a faulty addressing device such as its POPIT or Octopopit, or there may be noise on the zonex data loop in the field. New Installs - Only a few missing , verify the popits are addressed and wired to the correct zonex loop. (9000 Series Panels Zonex 1 is Addresses 9 to 127 and Zonex 2 is 129 to 247). If all on the same wire run verify the wiring from the last working popit to the first missing popit. Exsisting Install that all was working - All popits missing - Remove all wire from the Zonex terminals for the missing popits (9000 Series Panels Zonex 1 is Addresses 9 to 127 and Zonex 2 is 129 to 247). Only wire the D8125 to the correct Zonex (Out of the panel to In of the D8125  and In of the panel to Out of the D8125). This would remove any D8128 Octopopit Modules and D8129 Relay Modules from the Zonex. Next, remove all loop wiring from the + /- Terminals of the D8125. Using View Point Status fro the Keypad or RPS verify the State of all the popits on the loop by add ing 1 loop at a time until you connect the loop or loops that are causing all to go missing. Once you have the bad loop or loops isolated - Divide and conquor the loop. Go out halpf way and open the loop if the points work go out further on the loop if still missing move back toward the panel and open the loop.

How to determine which pins of the RJ45 and RJ11 are used for Tip and Ring or Tip-House/Ring-House.

How to correct the correctly programmed D1260 displays 'CALL FOR SERVICE'. The D1260 displays CALL FOR SERVICE even though it is programmed correctly.  

Part numbers D7212B, D9112B, D7212B1, D9112B1, D7212, D7412, D9112, D9124, D9412, D7412G, D7412G, D9124G, D9412G, D7412GV2, D7412GV2, D9124GV2, D9412GV2, D7412GV3,D7412GV3, D9412GV3, D7412GV4, D7412GV4, D9412GV4,